The territory of the car

Side mirrors improve the overview of the rear view, but, unfortunately, the side mirrors often break or come off. Movement with a broken side mirror can be very unsafe, especially in conditions of intensive traffic on the roads. Replacing side mirrors at the stations of those service can often cost big money. But this is a very simple procedure that every car owner can make with just a few special tools. Below in the article, we described a detailed action plan for removing and disassembling side mirrors.

How to remove the side mirror

How to remove (breed) side mirror

  1. Keep the car in the parking position. Turn off the ignition. Lower the glass down to the end on the side you want to change the glass on which you want to change the glass.

Mirror removal process

  1. Disconnect the negative battery terminal. This will avoid electric shock when working with electrical components in the mirror drive harness.
  2. Disconnect the negative battery terminal. This will avoid electric shock when working with electrical components in the mirror drive harness.
  3. Remove the internal door finish panel using the tool for removing and remove the finish elements. Find all the hidden screws in the mounting lid around the door panel. Remove all screws with a screwdriver. Place all the screws and details of the finishes in a safe place in order not to lose them.
  4. Remove the panel with the door. When removing the panel you need to be careful. Wiring is connected to the door panel. When removing the panel, make sure that the entire wiring is disconnected. Pay attention to how all the wires are connected so that you can connect them when mounting.

Removing the mirror

  1. Find the wiring harness and slowly disconnect it from the clamp. You might need a screwdriver to help click on the castle. Do not attempt to unlock it without a suitable tool. If you have manual windows, skip this step.
  2. Loosen the mirror mount nuts using a hex or screwdriver. Carefully remove the nuts and keep them aside. Gently pull the mirror.

Replacing the mirror

  1. Think if you need a new glass. If your mirror is not damaged, but the glass is broken or missing, you can simply replace the glass in the mirror. Replacing one glass may be impossible if you have a heating or an electric mirror! Check the manufacturer's recommendations before changing the glass.
  2. Contact the store of spare parts in order to pick up the maximum suitable glass in size.
  3. Carefully remove all fragments with a broken mirror.
  4. Clean the area inside the mirror with a loud fabric.
  5. After that, apply two-way tape or car quality glue, which is in any automotive spare parts store. Attach the mirror glass.

Video how to disassemble lateral mirrors

Installing rearview mirrors

To properly install the side mirrors on your car, simply repeat in the opposite sequence items that are described in the "How to remove a side view mirror".

More interesting Staths

How to remove and disassemble the side mirror of the rear view

The side mirrors of the rear view and the salon mirrors are mandatory installed on any car. At the same time, the side mirrors several act relative to the body, as a result of which their breakdown often occurs because of small traffic accidents.

Also, the side mirror may have heated, an electrically regulatory system, etc. During operation, such decisions fail, which requires replacement or repair of the side mirror.

In such a situation, the lateral mirror will need:

  • Remove from the car (revealed fasteners);
  • removing the mirror element and disassembly;
  • Perform a replacement or repair of damaged items.

At the same time it is important to know how to remove the sideline, as well as how to disassemble the side mirror correctly. Read more in our article.

In which cases you need to remove the side mirror of the rear view

How to remove the side mirror

Side mirrors on different cars differ in shape and sizes, may have limited or advanced functionality. At the same time, the main function is the ability to control the situation around the car.

On modern cars, mirrors with heating and electrically regulating, also often quite often in them is integrated an additional indicator of rotation.

Such "electronic" and "mechanical" solutions in the mirrors usually fail over time. Also, we should not forget about the traditional breakdowns of the side mirrors of the rear view (for example, in parking or as a result of minor accidents).

It often happens that in the process of long-term operation, there is a need to paint the side mirror after damage to flying stones, etc.

How to remove the rearview mirror

Removing the side mirror of the rear view

First of all, the replacement of the sideline mirror is not always needed. As a rule, only individual elements are changed or the mirror is repaired. As part of the repair, it may be necessary to replace the mirror element, restoring heating or adjustment functions. However, if the side mirror is badly damaged, then the complete replacement is performed with the case assembly.

To remove the side mirror:

  • It is necessary to reset the minus terminal from the battery (in the presence of heating, repeaters of turns and other solutions in the mirrors);
  • Then you should open the car door;
  • Next, the knob of changing the corner of the mirror is removed (in the presence of mechanical adjustment);
  • Then you will need to detect the mirror mounting bolts and unscrew them. Typically, such bolts are covered with a decorative lining (removed by a plastic blade or screwdriver);

    Please note if when disassembling panels, lining and other elements there are rubber seals, you must carefully remove them, because it will be difficult to find new seals for replacement.

  • Having twisting the mirror fastening bolts, do not rush to remove the mirror itself, as it is necessary to remember the position of the cables, connectors, pads, etc. (for example, electric mirrors);

How to disassemble the rearview mirror side

How to disassemble lateral mirrors

Disassemble the mirror is necessary for its repair. Often this operation is performed if the mirror member is replaced. In this case, the plastic case does not change. Also, the mirror element should be removed if it is planned to paint the side of the side mirror.

The disassembly of the side mirror is carried out as follows:

  1. The mirror element in the mirror housing is attached due to plastic latches (2 or 3 latches on each side). To carefully and safely remove a mirror from the case, plastic latches are recommended to warm up a simple household hairdryer. It is important to distribute heat over the surface of the mirror, as well as not to use high heating with a construction hairdryer. Ignoring this rule may result in placing the hull and latch.
  2. After the latches become softer, you can remove the mirror. This is done using plastic blades or a flat screwdriver, which is pre-wrapped with a tape (protection against scratches on the body and on the mirror itself);
  3. To remove the mirror, in the slot between the mirror part and the housing is embedded with a piece of softwood, after which you can push the blade or screwdriver. As a result, a lever is obtained, which can be shifted by the mirror;

    Gently affecting the mirror element, you should pull the blade, insert one more. In a pair, the blades or another lever will allow you to deduce the mirror from the mount. Usually one side is first declined, after which the other is differently disconnected.

  4. After complete disconnection, it is important not to immediately move to the removal of the mirror, since the wires can be connected to it. Connectors need to be carefully disconnected, after which you remove the mirror element. It will also be necessary to unscrew the bolt fixing the central frame frame;
  5. Now you can perform the necessary work on repair or replacement. Upon completion, the assembly of the side mirror is carried out in reverse order.

Other ways to remove the car mirror

Removing the mirror element of the side mirror

If a structural side mirror is a simple or mirror element already damaged and requires a replacement, it is enough to perform the following to remove the mirror element:

  • A soft lining is stacked on a flat surface;
  • Next, the casing of the mirror should not be severely hit on the lining;

As a rule, the mirror element in this case "scores" from the latch, and without damage (relevant for entire rear-view mirrors, which are disassembled for repair). Next, it remains only to remove the element completely and perform repairs.

How to remove the tape recorder without keys

We also recommend reading the article about

how to remove the tape recorder without keys

. From this article, you will learn about the ways of removing the radio in the car without key-puller, as well as what nuances should be paid to the implementation of this procedure.

Please note that this method makes it possible to understand how to remove the rearview mirror, but in the dismantling process will require maximum accuracy. Cause - There are always risks to damage the mirror or its housing.

However, on simple side mirrors (without heating and electrically regulating), this method of removing the mirror element allows you to significantly save time and simplify the procedure (subject to proper execution).

Recommendations

On different models of cars can stand various side mirrors. This means that before removal, separate design features must be taken into account in advance. In some cases, you will need to remove decorative lining, panels, etc. Only then access to the screws of the mirror housing will open.

When removing the mirror element, it should be borne in mind that the space under the mirror element is not necessary to be "empty". As a rule, modern cars inside the mirror housing have hidden adjustment mechanisms, turn repeaters and other elements. For this reason, the replacement of the side mirror should be carried out taking into account the design features of the mirror on the car.

It should be noted that the replacement of the original mirror element is no cheaper analogue can lead to the fact that the "quality" of the image in the side mirrors when compared with the original will differ significantly. Moreover, even the shade and color of the mirror element can be different compared to the original.

Also, subject to the presence of a heating function, the original mirror can warmly warm up, the warming zone may be limited (heating is not over the entire area), etc. To avoid similar troubles, experts recommend using only original mirror elements for replacement, even taking into account their higher cost.

Any car enthusiast will not ride without a mirror of the rear view. But this simple device fails. Fastening the salon mirror sometimes suddenly weakens. And the external mirror someone can hurt and accidentally smash.

In addition, an angle adjustment drive is periodically breaking in the mirror. Is it possible to solve all these problems yourself? Of course: to disassemble, remove or glue the mirror yourself for most car enthusiasts. It is not as difficult as it seems.

Removing the outer and inner rearview mirrors

Rear view mirrors are an integral part of the car. Even those drivers who equip their "swallow" with a monitor or camera cannot do without mirrors. Therefore, keep them in good condition - the first task of each car owner. Before switching to the procedure for disassembling mirrors, list the toolkit that we need to work.

Required to dismantle tools

  • shirling cross;
  • Shutter with flat sting.

How to disassemble an external mirror

Disassembly of outer mirrors expediently implement in a certain sequence.

  1. Using the screwdriver, a locking bracket is removed, to which the adjustment angle of the mirror is mounted. How to disassemble lateral mirrors? 4 waysThe locking bracket of the side mirror is extracted using a crosswinter
  2. The same dummy turns the mounting screws. There are only three of them. During the extraction of these screws, the mirror must necessarily hold. How to disassemble lateral mirrors? 4 waysSelf-tapping screws holding a side mirror, unscrew the crossed scold
  3. After removing the screws, the mirror is removed. To do this, it needs to be slightly pulled. How to disassemble lateral mirrors? 4 waysAfter removing the screws, the mirror is removed manually

How to remove the salon mirror

Change the rear view mirror in the cabin is a bit more complicated. Works need to be carried out in such a sequence:

  1. Plastic plugs over the fastening screws of the salon mirror are neatly approaching a flat scolder and removed.
  2. Fastening screws are unscrewed by cross scolding. How to disassemble lateral mirrors? 4 waysFastening screws of the salon mirror twisted with crossed scolding
  3. The mirror is neatly removed.

How to spare the mirror from the windshield

Conducting a dismantling of the glued mirror does not require special skills. Act as follows:

  1. In some modern cars, the bracket with the cabin mirror is glued straight to the windshield. To remove it, you must remove all plastic plugs from the bracket (if any).
  2. After that, the mirror turns the two hands counterclockwise and removed from the socket. How to disassemble lateral mirrors? 4 waysThe glued mirror rotates 90 degrees and is removed by hand

Disassembly of rearview mirrors

The procedure below is used for both external and internal mirrors.

  1. The mirror is removed from his regular place.
  2. Hand should be gently pressed on the top edge of the mirror glass until it turns out. How to disassemble lateral mirrors? 4 waysMirror element of the side mirror turns manually
  3. In the slot, which occurred between the mirror body and glass is placed a piece of a vet or a napkin.
  4. Then a flat spun, pre-wrapped with a tape, is also encouraged into this slit. How to disassemble lateral mirrors? 4 waysLockers holding a mirror element, rejuvenated with flat scuffers
  5. Lockers holding the mirror are subject to scolding and removed from the protrusions.
  6. Mirror glass is carefully removed.

The left mirror is dismantled in the same way as the right.

How to glue the cabin mirror to the windshield

To begin with, decide on the glue that we are going to use.

What glue you need to use

The main rule: the glue holding the cabin mirror on the windshield must be two-component. Yes, there are many varieties of universal glue.

But in this case, the universal glue is not suitable. The fact is that two-component glue perfectly withstands harsh temperature differences, high humidity, and most importantly - vibration.

Conclusion: The mirror element should not be glued to universal glue.

There is a second option: use the light-cured glue. This substance that is quickly "grasped" under the influence of sunlight. Such glue can be purchased in specialized auto shops.

But he has a serious minus: there is a powerful ultraviolet lamp to work with it, without which the reliable gluing is not achieved.

Some car enthusiasts claim that it is possible to do without it, it is enough to just glue the mirror with a sunny summer day. But it is impossible to name such a gluing.

The output is simple: the best and least troublesome option for gluing the mirror is two-component glue. For example, Loctite 37438, which has recently become incredibly popular. By the way, it is sometimes used to glue from video recorders, which weakened the fastener device.

How to fix the mirror element

So that the mirror holds reliably on the windshield, it is necessary to act according to the following algorithm:

  1. Selects the place of installation of the mirror. It must be glued in the center of the glass, at the same distance from both the passenger and the driver.
  2. The windshield is cleared of contamination. Initially, this is done with the help of a vet, then the glass surface is cleaned with alcohol.
  3. The mirror disassembles as indicated above (after all, in fact, only the bracket on which the mirror will be installed) should be glued to the glass.
  4. The thin layer of adhesive is applied to the bracket and on the windshield. After that, it is necessary to wait at least 15 seconds. How to disassemble lateral mirrors? 4 waysGlue is applied to the cabin mirror bracket
  5. The bracket is then installed on the windshield and slightly pressed manually (and if it is decided to install the mirror completely, without disassembly, then after installing it, it is necessary to further fix the scotch, which will support the mirror until the glue is grabbed). How to disassemble lateral mirrors? 4 waysThe cabin mirror is glued to the windshield
  6. The glue should dry, so that during the day it is impossible to ride the car.

Video: We glue the mirror to the glass inside the cabin

Installing a device on a bolted mount bracket

Not on all modern cars, salon mirrors are glued to the windshield. In some cases, the mirror bracket is attached in the old manner: bolts to the ceiling. In this case, you need to act like this:

  1. The mirror together with the mounting bracket is installed in the ceiling niche and sticks with hand. How to disassemble lateral mirrors? 4 waysThe salon mirror is installed in a niche and sticks with hand
  2. The screws are inserted into the holes and tweaked with the help of a crossover.
  3. The sockets with installed screws are closed with plastic plugs (provided that those are provided in the bracket design).

How to install and fix side mirrors heated

To make yourself assembled and connect side mirrors, you will need minimal knowledge in the electrician and skill. It is necessary to act in such a sequence:

  1. A set of mirrors equipped with an internal heating system was purchased. Heated with heated for Lada Grant car
  2. From the car removed the regular side mirrors in the way that was mentioned above.
  3. After installation, the top cover on the body of the side mirror opens. Access to the wiring connections jack (it is supplied with mirrors). Outputs the side mirror housing and connects electrical wiring
  4. The wires are connected to the socket and through the mirror housing are at the door.
  5. With the door of the crosst hole, plastic cover is removed. The door of the car removed the plastic cover
  6. Wiring is pulled through the door and dashboard to the fuse block, next to which the relay is with a plug to turn on the heating of mirrors. Conducting mirrors connects to the heating relay
  7. The posting plug is connected to the jack shown in the photo, after which the vehicle's door taking reverse assembly is made.

Common device malfunctions

Consider a few troubles that every car enthusiast may encounter.

Out of a mirror surface

Sometimes this trouble occurs even on new cars. Causes can be the most different.

  • The manufacturer decided to save and used low-quality adhesive composition;
  • During the work, the master did not allow glue to be captured;
  • The mirror was broken due to too sharp temperature differences (and this is the most common cause, especially frosty winter).

In all these cases, the car owner will have to use two-component glue, as shown above.

Procedure for replacing glass

The mirror element of both an outer and salon mirror may be damaged. Below is the sequence of its replacement:

  1. Glass is extracted from the mirror body.
  2. The new mirror element has several plastic hooks (in our example 4). These hooks are introduced into the fasteners in the mirror housing, after which it takes a very gentially pressing on the mirror element. One mirror element is installed in the mirror housing manually
  3. The characteristic click, saying that the plastic hooks joined and the glass "village" in place.

The procedure for replacing the mirror elements in the salon mirrors is similar to the one that is given above (the only difference is plastic latches in the salon mirror, as a rule, 2, and not 4).

Video: how to assemble and change the mirror element

The rear view mirrors are able to deliver a lot of trouble by car owners. But fortunately, most of these problems are solved on their own. Removal and securing the mirror element can be performed on their own. The main thing is to act as careful and not forget that the glass is an extremely fragile material.

  • Alexey Stepanov
  • Print

2017-07-06

Many motorists are concerned about how to open the trunk if the castle of the car broke. Currently exists ...

A source: https://autozam.ru/soveti-po-ekspluatatsii/kak-razobrat-zerkalo-zadnego-vida.html

Disassembling side view mirror

Author Peklo

Discussion of the report, questions on the topic on the forum.

Pay attention to rusty screws! The mirror stood on a neighbor's car around 2 years. I have them in the same condition, however, in the summer I stuck them with a 3m 3m square meter in the heat and rain - there is not even a hint of a dug. See what will happen after the winter.

  • How to disassemble lateral mirrors? 4 ways
  • So, proceed.
  • We press the top of the mirror (do not forget that in the photo it is turned off) with a finger until it stops. How to disassemble lateral mirrors? 4 ways

Over the other hand, the resulting gap (and again with a finger). Wide the white plate in the center of the mirror. In her ends, closer to the edges (marked by the arrow), there are tweed widths. It is the diverge to insert there and turn 90 degrees. A click is distributed, this edge of the mirror acquires some freedom. We repeat the operation from the other edge.

How to disassemble lateral mirrors? 4 ways

What do we see?

№1 - Stalls, holding the bottom of the site (we just laid them down). №2. - M-shaped brackets holding the top of the mirror. They are clearly visible in the following picture. Just pulling the mirror from this position, we completely free it.

Number 3 - knife contacts that are heated by the mirror. They are simply alternate. After a while, next to the white platform (I forgot to designate), a spring rack is visible (it is also visible in the next picture). In the assembled state, it rests on the mirror body.

IMHO, needed to eliminate all sorts of backlays and rattling the mirror.

How to disassemble lateral mirrors? 4 ways How to disassemble lateral mirrors? 4 ways

By reloading the central screw and pulling on itself, remove the white item from the gear motor. At the same time, one more details will be rated with it (the cuffs are not counting: one starred, and the second remained, closing the gear).

№№1,2 - Surrounding axes, one end of which (we are not visible) ends with a ball, quite strongly pressed into a white plate. It is quite moving.

The second end of each axis ends with a cup of five round racks at a smaller radius, and one rack for more radius. This rack is higher than the rest, i.e. Sit down deeper into the gear slot.

As a collected form, the high stand is included in the grooves of gears (4), and five others rest in the ends of oblique teeth on the gear. Thus, if, for example, the upper gear turns onto some kind of angle clockwise, then five racks will rise by oblique tooth, thereby putting forward the axis up.

And vice versa. Follows that the axis №1 Mills the mirror in azimuth, and the axis №2. At the corner of the place. Dethal Number 3 - Polusfer, which relies the plane of the mirror, i.e. Rotation point.

  1. How to disassemble lateral mirrors? 4 ways
  2. By revealing the three self-pressing, we liberate the gearbox itself.
  3. How to disassemble lateral mirrors? 4 ways
  4. Halves of its housing are kept on 4 snaps.
  5. How to disassemble lateral mirrors? 4 ways
  6. By pressing the petals, reveal it.
  7. How to disassemble lateral mirrors? 4 ways

We see two electric motors and two gears. Bottom on gears sliced ​​teeth. The gears themselves have a small backlash.

IMHO, thanks to this backlash, we hear a characteristic crackle when we try to "make a mirror" in extreme positions, or try to move the mirror, and it squeezes to the case: the worm pushes the gear to the side and jumps on its stationary tooths. For a long time I was looking for an electric trainer in a hair dryer. In my opinion, it is that!

Discussion of the report, questions on the topic on the forum.

A source: https://tcorolla-club.ru/fotootchety/samostoyatelnoe-to-i-remont/razdel-izzov-i-kuzovnye-evementy/razborka-zerkala-bokovogo-obzora/

Disassemble the cabin mirror is not very difficult

How to disassemble lateral mirrors? 4 ways

How to disassemble the salon mirror

It all started with the fact that I bought a monitor, which is attached to the salon mirror. And as he is sufficiently heavy, the mirror kept, and how to strengthen it did not know. Infroved to glue, it is inconvenient when you need to turn the monitor, I had to tear off the glue, I picked up all sorts of gum, plastics, tried silicone, did not help anything.

And I had to experiment with the disassembly of the mirror itself. After long torment and attempts, I found a way to disassemble the salon mirror.

First you need to hide the cover covering access to three screws to the mirror and remove it.

How to disassemble lateral mirrors? 4 ways

Then unscrew the screws holding the mirror with the hand so that it does not fall. To gain access to the mechanism of rotation of the salon mirror. You need some subtle, but durable item, I used the Temples for the hair, so they call my daughters.

How to disassemble lateral mirrors? 4 ways

The chpox should be inserted between the mirror and the plastic casing with a side, not on top or bottom, but with a side, and slightly squeeze the mirror outward.

How to disassemble lateral mirrors? 4 ways

It should be quite easy to get out of the sinuses. Everything needs to be done neatly so that the chips do not get or burst the mirror. I had to disassemble the salon mirror three times.

The small chip turned out for the first time, after an experiment with a screwdriver. When disassembled the first time, it turned out that the hinge connection was weakened. Pulled it up with an adjusting screw and assembled the mirror in the reverse order.

The second time I disassembled, after it was randomly replant with the driver's seat, on the rear passenger. In this time a plastic object was broken from the mirror rotation hinge clamp.

How to disassemble lateral mirrors? 4 ways

To get it to have to disassemble the whole mechanism. To pull the part from the clamp used scolding.

How to disassemble lateral mirrors? 4 ways

When disassembled, then a thin drill neatly drilled a hole for almost the entire length of the clamping. In the hole, for reliability flooded with epoxy resin, picked up the length and inserted the screw.

Collected everything back, pulled up the adjusting screw. The mirror was held quite firmly, and no longer resulted, until he was hit by, placing the kids in the car. It was enough to disassemble the salon mirror for the third time. Obuvera discovered that the same part was broken, only already bursting in another place.

It used an aluminum plate and four screws for its compound.

How to disassemble lateral mirrors? 4 ways

Tightening, thus the burst of the place, gathered the mechanism, pulled out, put the mirror in place and installed the salon mirror into the car.

Details of the disassembled salon mirror.

How to disassemble lateral mirrors? 4 ways

how to make a car radiator

Share the article in Soc. Networks:

A source: http://7ya-i-ya.ru/avtolyubitel/kak-razobrat-salonnoe-zerkalo.html

How to disassemble lateral mirrors?

How to disassemble lateral mirrors?

How to disassemble lateral mirrors? 4 ways How to disassemble lateral mirrors? 4 ways How to disassemble lateral mirrors? 4 ways

Why disassemble the side mirror of the car? To do this, there may be several reasons: troubleshooting, repair and maintenance, or installing new parts of the mirror after damage. All these types of work can be performed by car service specialists, and these services are not the cheapest. That is why many motorists are engaged in the repair of their car on their own.

Let's find out how to disassemble the side mirror and that it may be needed for this. The fact that there are many brands and car models, and each car can have their own specific type of mirrors with its technical characteristics.

Disassembly of the side mirror

In order to disassemble the side mirror, we will need the following tools:

  • Set of crusades;
  • A set of flat screwdrivers;
  • Knife, plastic or metal blade.

Suppose that we need to disassemble a mirror with an electric drive that regulates its position.

  1. Before proceeding to work, disconnect the battery terminals.
  2. In the cabin neatly pip the plastic triangular plug, which closes the mirror fastening bolts.
  3. After removing the plug, you must neatly disconnect the block with the drives of the drive. How to disassemble lateral mirrors? 4 ways
  4. After that, unscrew several bolts with which the mirror is attached to the door. Usually such bolts are only three.
  5. By reloading the bolts, you can safely remove the mirror from the door of the car.
  6. In order to deduce the mirror itself, it is necessary to pose it with a shovel or flat screwdriver. If you use a metal blade or screwdriver, the tip of the tool that comes into contact with the mirror must be wrapped with a tape. So you do not scratch the surface of the mirror.
  7. After the mirror surface is extracted, the side mirror housing will be ready for further disassembly. Remove the panel to which the mirror surface is attached. Under the lid is the mechanism that is responsible for turns of the mirror.

Now you know how to disassemble a side view mirror. Further analysis is individual for each brand of the car, because all side view mirrors have a different design. If you need repair or care instructions for other parts of the car, you should visit the car repair section.

A source: https://elhow.ru/tehnika/avto/remont-avtomobilja/kak-razobrat-bokovoe-zerkalo.

How to remove the side mirror of the rear view

The side mirrors of the rear view are the most commonly damaged parts of the automotive body, as they advocate the main dimensions. Therefore, it is often necessary to replace the entire structure, if it is not very lucky, or only a mirror plate, which may come into disrepair for various reasons.

Often you have to shoot a mirror element when it stops working. In this case, it is necessary to be particularly careful not to damage the whole and quite suitable reflective plate. Of course, you can contact the car service. If there is no such possibility for any reason, it is necessary to engage in the removal of the mirror.

That is why, many motorists are interested in the procedure of action, with which it would be possible to remove the mirror plate or the entire mechanism that is attached to the car door assembly. Let's look at some ways that could help remove the rearview mirror.

How to disassemble lateral mirrors? 4 waysSide mirror device

Side mirrors

Unfortunately, with unwanted mechanical contacts with any items, in most cases, not only the mirror plate is damaged, but also other elements of the mechanism. Therefore, you have to remove everything completely from the door, in order to replace or repair.

It is clear, the rearview mirrors depending on the car model, they can differ in both shape and "filling". Rear viewing devices can be equipped with such additional options:

  • heating the mirror element;
  • rotation repeater;
  • Elements of tuning in the form of built-in LEDs.

All the auxiliary fixtures listed above are spoiled from the onboard power grid. Therefore, before you begin to remove the side mirror, it is worth disconnecting a minus terminal from the battery, in order to prevent the possibility of a short circuit.

How to disassemble lateral mirrors? 4 waysSide Mirror with LEDs

The following actions that are performed from the inside with usually open doors, in most cases there will be such a sequence:

  1. The lever of the rotation of the mirror mechanism is removed, for which it is usually worth carefully drawing on himself. This advice is not universal, since here a lot will depend on the car model.
  2. Now it is necessary using a flat screwdriver to remove the decorative plastic lining, which closes the fasteners and the rotation mechanism of the rearview mirror. Please note here, most likely, there must be rubber pads, which are desirable not to lose, because they are unlikely to find on sale separately.
  3. After removing the plastic protection, access to the three fastening bolts that need to be unscrewed are available. Also here is the drive of the rotation of the mirror, which is attached to two bolts. Removing the joystick, you need to remember the correct location of the multicolored cables available here, so as not to confuse them when assembling.

If the mirroring mechanism is equipped with an electric drive, it is necessary, before removing the mirror, disconnect the terminals passing electrical wires here.

How to remove the mirror plate

The need for removal of the most "glass" may arise due to many reasons, including:

  • replacement of failed heating elements;
  • Replacing LEDs;
  • Replacing the rotor repeater lamp.

Removing the rear bumper VAZ 2114

For this procedure, such tools and devices may be needed:

  • one or two flat screwdrivers;
  • plastic or wooden wide shovel;
  • flap soft tissue or tape;
  • hairdryer.

It is clear that the main task when performing such a manipulation is to preserve the mirror plate in the intact state, so it is necessary to work carefully and slowly.

In most modern models, the glass detail is attached to the housing using several plastic latches, which can be from 4 to 8.

Work just will be to gradually "disrupt" a reflective plate with fasteners.

note

So why start. In order for the plastic mounts to become softer and pliable, you can warm up them.

To do this, you will need a hairdryer, but not building (it is too hot), and the most ordinary, household.

It is necessary to warm up for 2-5 minutes (depending on the ambient temperature), directing the stream of hot air on the glass. After heating, you can try to disconnect the mirror from the case.

How to disassemble lateral mirrors? 4 waysFastening a mirror plate

For this we do the following:

  1. The reflecting glass must be pulled down down and slightly to the door, which will increase the upper gap between the mirror and the case;
  2. Now we use the blades or screwdriver, in the absence of the first. To make metal screwdriver tips softer, they should be covered with a sparkle. Under the plastic edge of the case to not damage it, the soft (bike, flannel) fabric is placed;
  3. The shoulder blades or screwdrivers are starting behind the mirror in the location of the upper latches (after the glass is delayed down, the attachments become visible). Now you need to gently pull the levers towards your own belt;
  4. After the mirror plate is freed from the upper fasteners, it will become much free to shifted, which will make it possible to make your fingers to the upper edge and to release the lower latches and remove the reflective plate;
  5. After removing the glass plate, access to the optical elements to be replaced, as well as to the rearview mirror heating system. Further actions are directly dependent on the car model, as the devices hiding behind the reflective plate may have a variety of design features.

To put the mirror in place is always much easier. You do not need to warm here. It is worth correctly combining the latches, which is usually not difficult and put pressure on the reflective plate with an effort.

So we figured out how you can remove the mirror plate using non-hard tools, and also separate the entire device assembly from the door. As you can see, there is nothing difficult, although, without having experience, it will have to tinker a little.

Check car body geometry

A source: https://okuzove.ru/remont-kuzova/kak-snyat-bokovoe-zerkalo-zadnego-vida.html

How to remove a mirror element?

With the problem of replacing the mirror element, almost every driver faces, as the mirror can crack or crash during adverse weather conditions or accidents.

Now it was very popular to change the mirror element to a more improved, heated.

It is dangerous to ride a cracked mirror, as the damaged element distorts the real image and can entail an emergency on the road.

1

Dismantling of the mirror with your own hands

To change the mirror element to a new one, first of all it is necessary to dismantle the mirror. Certify this may even beginner, the only condition is to have a standard set of screwdrivers with it. The example shows how to remove the side mirror of the rear view, but this method can be applied to dismantling any mirror in the car.

  • 1 stage - open the driver's door;
  • 2 Stage - Pull the handle of the mirror angle (if the handle is not removed from the grooves, then unscrew it against the clock of the arrow);
  • 3 Stage - Unscrew the mounting bolts if the handle is not removed;
  • 4 Stage - With a flat screwdriver, very carefully remove the plastic overlay, so you will be visible to the fastening elements that need to be unscrewed;
  • 5 Stage - unscrew the bolts that are responsible for the rotation mechanism of the mirror;
  • 6 Stage - Gently remove the mirror.

If you change the mirror element for the first time, then all the disassembly stages advise to photograph. Especially remember the location of multi-colored cables, which are connected to the rotary mechanism.

Get a mirror element from the housing, while without damaging it, the work is quite paintaking. Plastic latches may especially be injured, so all the steps need to perform slowly and follow clear instructions:

  • 1 stage - using a conventional hair dryer a little warm the plastic latches, so the mirror element will be easier to reach (a hairdryer does not use at full power and not quite close to the mirror);
  • 2 stage - wrap a flat screwdriver with a tape (especially the metal part) and check whether the screwdriver "crawl" between the plastic base and directly with the mirror element;
  • 3 Stage - Take a small piece of soft tissue, not very dense (the terry towel is definitely not suitable) and put it to the plastic part, where you will overtake a screwdriver;
  • 4 Stage - Shoot a screwdriver under the mirror element and pull it very carefully (a screwdriver serves as a certain lever);
  • 5 Stage - 3 and 4 steps to repeat on all sides;
  • 6 Stage - After from all sides, the mirror element was released from fasteners, it can be carefully dismantled.

The new mirror element can be delivered by observing the stage in the reverse order.

Working with the replacement of the mirror element is very painstaking. It does not require a rush. If you fulfill all the steps and clearly act according to the instructions, there will be no problems with the dismantling of the mirror. We advise not to buy a mirror element without a quality certificate, it is better to turn to official representatives of the brand of your car.

A source: https://sovetclub.ru/kak-snyat-zerkalnyj-evement

How to replace the side mirror with your own hands?

12The removal of the car's lateral mirror is a very common car malfunction.

Quite often, during the coincidence, as well as during an inaccier driving, there is damage to the side elements of the car. At the same time, the side mirrors of the rear view often suffer. There are several reasons here.

First, the side mirrors are an oversized element, and the exposure to their lateral damage is very large.

Secondly, drivers of other cars, incorrectly appreciating the dimensions (at dusk or at night), can cause damage and tear off the side mirror.

Also, on the track it is possible to enter small foreign objects, leading to negative consequences in the form of cracks and chips.

The fault of the side mirror is a violation of the rules of the road, for which an irresponsible motorist can be fined to a large amount of money. As well as intentional emergency creation on the road, leading to a decrease in people's safety.

But after all, the emergency situation happened to you. The side mirror turned out to be damaged. To begin with, do not panic, but think well. Any mirror can be replaced in a short time. And the main issue here is your budget.

How much is the side mirror?

If there is a desire to replace the mirror from the official dealer, you will have to pay a large enough amount. For example, the simplest mirror of the budget foreign car will cost 6 - 7 thousand rubles. But usually dealers do not change separately the mirror - they work with modular structures.

It will be necessary to replace the mirror housing, adjustment drive, heater and glass. Together with the work of the staff, it will cost more than 16 thousand rubles. Of course, it is imperative to be repaired by the official dealer - this is the optimal version of the time and quality of work.

But if the hands of the motorist grow from where it is necessary, and the money under the pillow is not added at night, then everything can be done on their own. No gods burn the pots.

How to disassemble lateral mirrors?

First you need to decide on the brand of car and its constructive device of the mirror. Then to inspect the visible damage, and read the repair instruction. At about half of the cases, the side mirror malfunctions are to break the housing and broken glass.

Despite the fact that different cars will require a different approach to replacing the mirror, one for them is similar. If the mirror cracked, it is necessary to pull out from the holding hinge bracket, providing mobility, a bundle with a mirror, and then replaced with a new one.

The main thing when installing do not overdo it! The mirror is very fragile, so the procedure is better done at positive temperatures; In winter in a heated garage or service.

How to replace the side mirror?

For lovers save and work with their own hands, the mirror replacement can be carried out in the range from 500 to 1000 rubles. In order not to order a buckle with a mirror from an official dealer for a large amount of money (up to 5000 rubles), we find a high-quality non-original from China. Online stores of spare parts for you to help.

We remove the glass holder from the hinge of the protective casing, and then with the help of a thin chisel or a flat screwdriver, we take off the remnants of the previous one, the native mirror. The surface, if necessary, is leveled with a skin and degreases with alcohol or acetone. Now the new mirror must be glued.

The optimal glue option is pixipol, and silver - as it holds a lot better than transparent. Gently apply glue into the fastener shape of the burdock, and it is necessary to start from the center, and to finish without reaching about one centimeter to the edge - to eliminate the possibility of clearing the glue, and its ottes. We are waiting for a while, while glue is polymerized.

The final stage - gently insert the bundle with the mirror in the hinge fastening.

How to set up a side mirror?

Good visibility in the car is simply necessary to ensure ride safety. Car owners who believe that the car feel well, and are able to ride without mirrors - greatly exaggerate their capabilities.

In our country, cars with broken mirrors often become victims of scammers, and then it is very difficult to prove to their right point. Therefore, in addition to the mirrors must be, they should still be configured correctly.

The view from the driver's chair should allow an overview in all directions. Ask comrade bypass around the car for the trunk. At the moment of disappearance from one side mirror, a person must immediately appear on average, and then in another side. There should be no dead zones. Side mirrors are configured on a flat empty road.

Important

When the driver sits in an optimal position for himself, he should without turning his head, only with his eyes to see the back wing of the car not more than a fifth verical part of the side mirrors. The line of the end of the smooth road should divide the three mirrors in equal shares - the bottom and top.

Such a review is optimal both when driving in a dense stream with frequent rebuilding and in parking actions. It would be very useful to purchase additional glass, fastened to the side glass, and allowing you to see the rear wheel.

It is very convenient to control borders with parallel parking and movement by reverse in the urban area.

A source: http://mashin-ko.ru/statya/remont-i-etakspluataciya/stekla/kak-zamenit-bokovoe-zerkalo-svoimi-rukami.

How to disassemble a car mirror - disassembling the side mirror

How to disassemble a car mirror

There are many reasons for paving the side automotive mirror. It may be desire to paint it, or put in order after it hooked some kind of Likhach.

How to disassemble the automotive mirror, and before that, how quickly and easily remove it, interests many motorists.

From inept movements, the car mirror can completely come into disrepair and then buying a new one will be necessary, and as a result, the installation of the mirror in the car service will be followed.

But the brands and the more models of cars a lot, as well as mirrors for them. Also a lot and varieties of mirrors - with electric drive, folding, with elements of turns, and so on. The most important thing is how to remove not to damage. Below are the overall actions on the analysis of the side automotive mirror.

Removing the mirror

Naturally, it will be more convenient to disassemble the mirror removed from the car, so it should be removed. What is needed for this?

Removing a mirror with a mechanical drive. To begin with, remove the locking bracket of the mirror regulator, unscrew the three screws that fasten the mirror to the door frame, and then remove the mirror itself.

Removing mirror with electric drive. The first thing to do is disconnect the minus terminal from the battery. Next you need to disconnect the block with the wires of the drive, turn the three screws of the mirror mounting to the door and remove it.

Disassembly of the mirror

You can disassemble the car mirror in several ways.

First method

Using a curved object or screwdriver, deduce the mirror, gently pressed on it from the inside. An attempt to deduce the mirror from the edge can lead to damage. Some motorists are used to remove the mirror element a wide variety of items.

These can even be all sorts of kitchen blades. Some wraink the edge of the spatula with a tape, so as not to damage, or rather, do not scratch the mirror surface. Others use one rigid blade - to fix the slit, and the second softer to turn it into the resulting gap.

Second way

In order to extract the mirror element, it is necessary to dramatically hit the housing on the soft object - it may be anything. In order to disconnect the mirror body itself from triangular mounting, you need to remove the spring, unscrew the adjusting traction and remove the pin. The assembly and installation of the mirror is carried out, as a rule, in the reverse order.

Detailed and universal way

In the car, you need to deduct a plastic pad that closes the mirror mounting screws. After removing the lining, you should unscrew the three screws that hold the mirror and remove it. After that, you need to carefully remove rubber gaskets -

If rubber gaskets damage, then buy new will be very problematic, they are rarely sold separately.

Now you should unscrew the two screws of the mirror adjustment joystick. The disclaimers of the joysticks themselves - the procedure is simple, you just need to carefully remember the position of the cables and the color, since different color is responsible for your adjustment.

Council

Next, you need to remove the three screws that are located on the lower plastic corner - it is most susceptible to damage during the operation of the car. After that, you need to remove it. How to shoot the mirror element has already been described above.

After removing the mirror element, you need to unscrew the four screws and remove everything else.

The easiest thing, of course, ask the familiar wizard or send a car to the car service if the mirror is replaced or its painting. But most owners used to repair their car themselves - after all, this is a significant saving of money.

How to disassemble the side mirror on the VAZ 2110, see the next video:

http://auto-wiki.ru.

A source: http://legkoe-delo.ru/remont-avtomobilya/avto/81839-kak-razobrat-avtomobilnoe-zerkalo-razborka-bokovogo-zerkala

Rear view mirror is necessary for each car. They are not the same on different models of machines, but perform the only function - expand the driver's horizon.

Unfortunately, a breakdown of these elements of the car becomes a frequent problem. This part of the car on the car park is most vulnerable. Any "neighbor" may accidentally knock the mirror. Unfortunately, when a breakdown of this kind, only one exit is to remove the damaged part and install a new one instead. However, such a sad situation is not the only reason for changing the mirror. This skill will be required during repainting a car or if the mirror surface of the scratched or cracked.

Side rearview mirror
Side rearview mirror

How to remove the side mirror of the rear view with their own hands

This accessory is not so simple as it seems. Most often, various devices are built into it. For example: turn repeaters, LEDs, heating parts. For this reason, before removing the mirror, it is necessary to reset the negative charge from the battery. It is necessary in order to minimize the likelihood of a short circuit during the work.

Replacing the side mirror of the rear view
Replacing the side mirror of the rear view

Tools that will be required for this repair will be found in every garage. These include: a set of screwdrivers of different sizes, household hair dryer, plastic blade, tape, small piece of soft tissue, wrench. In addition, attention will be useful to detail, caution and desire to do everything correctly.

Removal process. After a negative charge is reset from the car battery. You can proceed to dismantling. To do this, open the car door, remove the handle of the change of the corner of the mirror.

The process of removing the correction handle of the angle varies on separate models of cars. For example, on some, it is enough to pull the handle for yourself in order to come out of the grooves. On other models it will have to get out counterclockwise or, before removing, you will need to unscrew the bolts on which it holds.

In order to remove the mirror, you need to find bolts that hold it. As a rule, they are under the decorative lining and are located so that they would not be seen. The decorative hiding element needs to be removed. Often together in it removes a rubber gasket. It is important not to lose it due to the fact that these elements are not sold in stores separately, except for some exceptions. When the hiding pad is removed, the bolts are clearly visible. They need to be unscrew in addition, to avoid confusion when assembling, it is best to photograph the location of multi-colored wires.

How to disassemble lateral rearview mirror

This will be required if, for example, the mirror element crashed and need to be replaced. It is fixed in the case of plastic latches. As a rule, they are from the reverse side of the mirror surface. The amount of attachment data is different on various models of cars. In order for plastic fasteners more controlled, you need to warm them. This can help a regular hairdryer. The jet of warm air needs to be directed to the entire surface of the glass. Usually there is enough pair of minutes. In addition to the usual, household hair dryer, there is a construction. However, this operation is better not to be carried out with it. The fact is that the latter can heat plastic to melting point and damage fasteners.

When latches from the heat become softer, you need to take plastic blades or a flat screwdriver. Use a metal object, you must extremely carefully, it can scratch the glass or body. The lever method you need to dig a mirror from fasteners. Bloxt attachments are not the only thing that connects the mirror with the case. In addition to them, there may be glue or wires. You need to disconnect all unnecessary elements.

It is easier to put a mirror surface back much - you just need to combine the latches in the desired order and put pressure on the surface of the mirror.

Useful advice

Under the blade or screwdriver you need to put a small flap of soft tissue, it will help to avoid damage to the outer part of the mirror.

When removing the mirror surface with a screwdriver fasteners, it needs to be cooled. So the risk of damage to the remaining elements is reduced.

Side rearview mirror
Side rearview mirror

If the mirror was attached to the glue including, it is necessary to return this layer. It is important to use the correct, suitable glue. For these purposes, there are three varieties: chemically hardened, light-subsidized, epoxy compositions. The latter will act as it should only be dry. In other words, the item must be pressed in the right state for ten o'clock. Light-cured adhesive mixtures should be exposed to ultraviolet. For it, the lamp will be required, solar light is not enough. The glue mixture is perfectly suitable, which has the ability to harden with the help of chemical processes.

In no case cannot be used by the usual superal and adhesive tape. These funds do not have the desired properties, and the mirror will definitely fall over time.

How to remove the side mirror - tips and recommendations

The side mirrors of the rear view are the most commonly damaged parts of the automotive body, as they advocate the main dimensions. Therefore, it is often necessary to replace the entire structure, if it is not very lucky, or only a mirror plate, which may come into disrepair for various reasons.

Often you have to shoot a mirror element when it stops working. In this case, it is necessary to be particularly careful not to damage the whole and quite suitable reflective plate. Of course, you can contact the car service. If there is no such possibility for any reason, it is necessary to engage in the removal of the mirror.

That is why, many motorists are interested in the procedure of action, with which it would be possible to remove the mirror plate or the entire mechanism that is attached to the car door assembly. Let's look at some ways that could help remove the rearview mirror.

Side mirror
Side mirror device

Side mirrors

Unfortunately, with unwanted mechanical contacts with any items, in most cases, not only the mirror plate is damaged, but also other elements of the mechanism. Therefore, you have to remove everything completely from the door, in order to replace or repair.

It is clear, the rearview mirrors depending on the car model, they can differ in both shape and "filling". Rear viewing devices can be equipped with such additional options:

  • heating the mirror element;
  • rotation repeater;
  • Elements of tuning in the form of built-in LEDs.

All the auxiliary fixtures listed above are spoiled from the onboard power grid. Therefore, before you begin to remove the side mirror, it is worth disconnecting a minus terminal from the battery, in order to prevent the possibility of a short circuit.

Side mirror
Side Mirror with LEDs

The following actions that are performed from the inside with usually open doors, in most cases there will be such a sequence:

  1. The lever of the rotation of the mirror mechanism is removed, for which it is usually worth carefully drawing on himself. This advice is not universal, since here a lot will depend on the car model.
  2. Now it is necessary using a flat screwdriver to remove the decorative plastic lining, which closes the fasteners and the rotation mechanism of the rearview mirror. Please note here, most likely, there must be rubber pads, which are desirable not to lose, because they are unlikely to find on sale separately.
  3. After removing the plastic protection, access to the three fastening bolts that need to be unscrewed are available. Also here is the drive of the rotation of the mirror, which is attached to two bolts. Removing the joystick, you need to remember the correct location of the multicolored cables available here, so as not to confuse them when assembling.

If the mirroring mechanism is equipped with an electric drive, it is necessary, before removing the mirror, disconnect the terminals passing electrical wires here.

How to remove the mirror plate

The need for removal of the most "glass" may arise due to many reasons, including:

  • replacement of failed heating elements;
  • Replacing LEDs;
  • Replacing the rotor repeater lamp.

For this procedure, such tools and devices may be needed:

  • one or two flat screwdrivers;
  • plastic or wooden wide shovel;
  • flap soft tissue or tape;
  • hairdryer.

It is clear that the main task when performing such a manipulation is to preserve the mirror plate in the intact state, so it is necessary to work carefully and slowly. In most modern models, the glass part is attached to the housing using several plastic latches, which can be from 4 to 8. Work just will be to gradually "disrupt" a reflective plate from fasteners.

So why start. In order for the plastic mounts to become softer and pliable, you can warm up them. To do this, you will need a hairdryer, but not building (it is too hot), and the most ordinary, household. It is necessary to warm up for 2-5 minutes (depending on the ambient temperature), directing the stream of hot air on the glass. After heating, you can try to disconnect the mirror from the case.

Side mirror
Fastening a mirror plate

For this we do the following:

  1. The reflecting glass must be pulled down down and slightly to the door, which will increase the upper gap between the mirror and the case;
  2. Now we use the blades or screwdriver, in the absence of the first. To make metal screwdriver tips softer, they should be covered with a sparkle. Under the plastic edge of the case to not damage it, the soft (bike, flannel) fabric is placed;
  3. The shoulder blades or screwdrivers are starting behind the mirror in the location of the upper latches (after the glass is delayed down, the attachments become visible). Now you need to gently pull the levers towards your own belt;
  4. After the mirror plate is freed from the upper fasteners, it will become much free to shifted, which will make it possible to make your fingers to the upper edge and to release the lower latches and remove the reflective plate;
  5. After removing the glass plate, access to the optical elements to be replaced, as well as to the rearview mirror heating system. Further actions are directly dependent on the car model, as the devices hiding behind the reflective plate may have a variety of design features.

To put the mirror in place is always much easier. You do not need to warm here. It is worth correctly combining the latches, which is usually not difficult and put pressure on the reflective plate with an effort.

So we figured out how you can remove the mirror plate using non-hard tools, and also separate the entire device assembly from the door. As you can see, there is nothing difficult, although, without having experience, it will have to tinker a little.

[Democracy id = "4"]

[Democracy id = "6"]

Author: Catherine

It often happens that the fastening of the rear-view mirror is weakening, and the mirror holds poorly or disappears (perhaps someone hooked him on the go). It happens that the side mirror crashed or gave a crack - it needs to be changed. It may be necessary to repair the drive adjustment of the mirror.

You can contact the car service, and the mirror is attached to the place. But if there is no room nearby, you will have to act independently. The rear view mirror is extremely important on the road: the driver can follow the situation on the roadway in the area of ​​the review over the rear wings and rear bumper. The vehicle on different brands of cars are different: an inner mirror and side mirrors, conventional, folding, with electric and others. When removing and disassembling any mirror you need to be extremely neat so as not to damage the mirror itself.

What will be required for disassembly

In order to disassemble the mirror, you will need a tool:

• 2 flat screwdrivers (latches are packed).

• Thin long screwdriver and a piece of soft tissue (in order to wrap a screwdriver).

• Key-star to 10 or a regular replaceable bits screwdriver.

Attention! For disassembly of one mirror can leave for 15-20 minutes.

How to remove the mirror

how Dismantle the side mirror with electric drive (Assembly):

one. With the front door remove the triangular lining.

2. Swede connector wiring mirrors. Do not damage the wiring of the mirror heating!

3. Holding the mirror, turn out 3 mounting screws.

four. Remove the mirror assembly.

five. Installation of mirrors We produce in the reverse order.

Disassembling the side mirror of the rear view with a mechanical drive:

one. Remove the lock bracket of the mirror regulator.

2. Holding the mirror, turn out 3 mounting screws.

3. Remove the mirror.

four. Installation is carried out in reverse order.

How to remove the rear view mirror in the cabin car

The most common option to fasten the rear view mirror on the windshield - 2 bolts. Such fasteners are found on domestic machines. To remove the mirror in the cabin, act as the following order:

one. Remove the plugs on the bolts (if any).

2. Holding the mirror, unscrew the fastening bolts.

3. Remove the mirror.

four. Place of adjustment of the mirror to the windshield wipe with alcohol.

five. When installing the mirror, you need to trace the mirror "village" to the same place (Piglet on the windshield).

On a foreign car, the rear view mirror is glued to the windshield. To remove the mirror from the windshield, make such actions:

one. We remove all plastic plugs with your hands.

2. Moderately pull the mirror up (to the ceiling).

Attention! Follow the condition of the glued fastener. If everything is done correctly, the mirror will remain in the hands, and the bracket (it is not removed) - on the spot.

Properly apply power (when you pull the mirror up). If you overdo it, the windshield can crack. If the mirror has already descended from the place of the bracket), and you still pull it with it, you can accidentally sharpen the upholstery on the ceiling. On some models, the car is a special retainer in the form of a button (you should click on it).

How to disassemble a mirror, 2 ways

To make a replacement of a cracked mirror, you need to know how to disassemble the rear view mirror. You can only remove the mirror: it is convenient, and safely for the mirror itself. Rear view mirror can be carried out in two ways:

• After after removing the mirror from the door or windshield. This method of disassembly is safer for the entire mirror block.

• Disassemble the mirror without dismantling it from the place of attachment.

Attention! Without skills, this disassembly is not recommended to do. The disassembly of the side mirror of the rear view is quite feasible. But disassemble the mirror on the windshield is extremely undesirable: any clumsy action screwdriver - and the crack on the windshield is provided.

If you need to replace any element of the mirroring unit, the analysis of the rearview mirror is to be done. Fully disassemble the rearview mirror (lateral or from the windshield) can be acting according to the scheme:

one. Hairdryer warm the mirror housing (warm glue on which the mirror holds, softens, and it will make it easier).

2. Wooden blade or wrapped in a soft fabric flat screwdriver are trying to separate the mirror itself from the case. To do this, carefully (up-down) we upgrade the mirror with a thin tool.

3. Now disconnect the heating wires of the mirror (2 them).

four. There are 3 bolts on the adjustment mechanism. They need to unscrew.

five. Disconnect the wires from the adjustment mechanism.

6. We postpone the adjustment mechanism. Under the mechanism are fasteners.

7. First remove the rear top cover. Cover mounts are made in the form of the tongue. They need to be pressed towards each other. On the right side, the tongue needs to be pressed to the side (repel it out).

8. Slowly and neatly pull the lid on yourself.

9. Now disconnect the rear bottom cover. There is also a fastening tongue here. Press the tongue with a screwdriver and simultaneously with a knife (or flat screwdriver) push the tongue from the back cover.

ten. Gently disconnect the back cover. For the attachment of the rear-view mirrors, it is better to use chemical hardening glue.

Rules of repair

Repair Rules Repair Mirrors are the same for all kinds of mirrors:

• Repair of the mirror is better to exercise, after removing it from fasteners.

• The disassembly of the mirrors is safer in the removed form.

• Before picking up and pulling the mirror itself, warm the body with a hairdryer.

• Do not press with a lot of effort on the mirror - it can give a crack.

• Be extremely accurate when removing the mirror from the windshield (you can break the windshield or damage the upholstery on the cabin ceiling).

• Do not make sudden movements when disassembling the mirror block (you can break the heating wires).

• If it is impossible to replace the broken part of the mirror block, you will have to put a new mirror block.

Did you know? To glue the falling mirror in place, you first need to remove the remaining old layer of glue. But before that, outside the windshield, make the marker label (the mirror should sit in its place).

Subscribe to our ribbons in social networks such as Facebook, VKontakte, Instagram, Pinterest, Yandex Zen, Twitter and Telegram: All the most interesting car events collected in one place.

Fig. 8.49 . Disassembling rear-view mirrors

Press the area and the mirror so that the area B moves to you ( Fig. 8.49 ).

Insert the screwdriver in the groove and remove the glass from the base of the mirror.

Fig. 8.50 . Rear view mirror components: 1 - glass of the outer mirror; 2 - connector; 3 - lid; 4 - holder of the outer mirror

Remove the remaining components in the manner shown in the figure. 8.50 .

Fig. 8.51 . Disassembling the mirror housing

Be sure to screw the mirror holder with a screwdriver, click on the holder's ear and disassemble the housing ( Fig. 8.51 ).

Fig. 8.52. . Installing the mirror in the case

Press the mirror in the case so that the pin does not shift ( Fig. 8.52. ).

Finally collect in order, reversal.

Dismantling

You decide to make dismantling work with the subsequent installation. The question is now just how to remove and how to disassemble the element, so that then without any risks to return to its place. There will be a glass replacement or another procedure in the interval depends on the specific situation.

To make dismantling work, you need to take:

  • curly screwdriver;
  • flat screwdriver;
  • wrench under the size of fasteners;
  • hairdryer;
  • degreaser;
  • rag;
  • high-quality glue;
  • some free time;
  • pure garage;
  • good mood.

Add a pair of skillful hand to this set to the tool, and everything will be superbly.

As you understand, the rear and inner mirrors are removed in different ways.

Work in the salon

Let's start with the salon design. Here much depends on what kind of car you work.

Automakers use different fastening systems. Because repel from the specific situation. So, for example, different fasteners are used on such cars as:

  • Deo Lanos;
  • VAZ 2110;
  • Niva Chevrolet;
  • Ford Focus;
  • Renault Logan;
  • Chevrolet Cruze;
  • Lada Priora;
  • Lada Kalina;
  • Hyundai Solaris, etc.

Yet, mostly independently, the owners of inexpensive cars are done.

And here you can face more with glue and suction cups, or with bolts and screws. These are the most common installation methods.

On domestic cars mainly come bolts. Therefore, it will be easy to remove the design. The plug is removed, the key is taken and the fasteners are unscrewed.

But there are both glued brackets to the glass. Here you will first have to figure it out, is it really possible to divide the fastening element with glass at all. Most often, designers use clamps or rotary mechanisms. In the absence of such an opportunity, it is necessary to remove not only the bracket, but also the windshield itself. The glue holds the element is very tight, and therefore it will not be difficult to damage the lobobushka.

Look at the instruction manual. There will probably find the hint what exactly to do in the current situation. Sometimes it is better to visit the car service where experts will do everything neatly and clearly.

Dismantling on the sides

In the cabin everything is clear. Now you need to dismantle the design of the outer mirror. Left or right, here the roles are already big. Much more importantly, what type of design is used. In the side mirrors there is a drive. And it happens mechanical and electric.

Almost any car structurally allows you to get to fasteners through the doors. You just need to remove the trim. Again, we look at the manual for your car, since there are no universal instructions on this.

If you have a mechanical drive, then:

  • Removed the locking bracket of the existing regulator;
  • Surrounded mounting screws from the inside of the door;
  • The mirror itself is removed.

In the case of an electric drive, everything is somewhat different. You need:

  • raise the hood;
  • find a battery;
  • Remove the minus terminal from the battery;
  • turn off the shoe with wires;
  • Remove the trim from the door;
  • unscrew the fastep of the mirrors;
  • remove the element;
  • Rejoice in the result.

The last item is especially important. Speak to grab yourself even for small achievements.

Installation and fastening of rearview mirrors

Before proceeding to independent repair and disassembly of external and internal elements of the review, it is necessary to understand the principle of their attachment. The inner mirror of the rear view is attached in the car over the torpedo. Depending on the type of design, it can be installed either using special suckers on windshield, or mounted in the ceiling. In the latter case, the part hold the bolts or self-tapping screws. Sometimes you turn them out quite difficult, especially if the fasteners are above the ceiling lining. In such a situation, you will have to disassemble the entire roof of the car. It is especially difficult to do this if the backlight tuning was previously performed in the car.

External elements of the review are installed on the driver's and front passenger door racks closer to the car's hood. On older cars, most of which are already recognized as a rarity, the external mirrors are attached to the front wings closer to the radiator.

Adjusting the elements of the review depends on the price range of the car. If the machine refers to the budget segment, then the mirror setting is made exclusively in manual mode. If the cost of the car exceeded 20 thousand dollars, then its owner has the ability to adjust the mirrors either manually or remotely. By the way, in the latter case, the driver is forced to repair the elements of the review. This is due to the presence of fragile chips, which manufacturer sets in the housing of the rearview mirrors.

Removing the outer and inner rearview mirrors

Rear view mirrors are an integral part of the car. Even those drivers who equip their "swallow" with a monitor or camera cannot do without mirrors. Therefore, keep them in good condition - the first task of each car owner. Before switching to the procedure for disassembling mirrors, list the toolkit that we need to work.

Required to dismantle tools

  • shirling cross;
  • Shutter with flat sting.

How to disassemble an external mirror

Disassembly of outer mirrors expediently implement in a certain sequence.

  1. Using the screwdriver, a locking bracket is removed, to which the adjustment angle of the mirror is mounted.

    The locking bracket of the side mirror is extracted using a crosswinter

  2. The same dummy turns the mounting screws. There are only three of them. During the extraction of these screws, the mirror must necessarily hold.

    Self-tapping screws holding a side mirror, unscrew the crossed scold

  3. After removing the screws, the mirror is removed. To do this, it needs to be slightly pulled.

    After removing the screws, the mirror is removed manually

How to remove the salon mirror

Change the rear view mirror in the cabin is a bit more complicated. Works need to be carried out in such a sequence:

  1. Plastic plugs over the fastening screws of the salon mirror are neatly approaching a flat scolder and removed.
  2. Fastening screws are unscrewed by cross scolding.

    Fastening screws of the salon mirror twisted with crossed scolding

  3. The mirror is neatly removed.

How to spare the mirror from the windshield

Conducting a dismantling of the glued mirror does not require special skills. Act as follows:

  1. In some modern cars, the bracket with the cabin mirror is glued straight to the windshield. To remove it, you must remove all plastic plugs from the bracket (if any).
  2. After that, the mirror turns the two hands counterclockwise and removed from the socket.

    The glued mirror rotates 90 degrees and is removed by hand

Disassembly procedure

When the design was removed, you can start disassembly. If it is required, of course. You may have found a new mirror, the price of which is completely satisfied with you. Then this item can be skipped.

If necessary, disassemble the element, repel from whether internal or external one.

The salon mirror is disassembled as follows:

  • There is a place where the glass and the case are connected;
  • Spin is inserted;
  • pressed with a little effort;
  • the gap appears;
  • The mediator passes along the entire length of the gap;
  • The housing is divided into 2 parts;
  • Mirror is removed;
  • Everything else is located under it;
  • We carry out the necessary work.

You may also need to disassemble the car side mirror. Not fundamentally important, left or right.

Then the task is to remove the reflective element. Prepare to the fact that the instructions below are not suitable at specifically your car. There is a car on which everything is not quite so. Excuse me here, the manual is not universal.

But it is the following scheme that is suitable for most cars.

  • With the help of a hair dryer, the zone of the connection of the body and glass is heated;
  • Do not heat up to high temperature. Use household hairdryer at medium power;
  • A flat screwdriver is separated by a body for 2 parts;
  • Sometimes it is required to bend terminals;
  • If you are afraid to damage the mirror, wrap the tool with a tape;
  • On some cars, it is necessary to slightly press the mirror in the center and lead to the side;
  • Glass is carefully removed;
  • The screw from the plastic frame is unscrewed if it is;
  • Under the frame we see the whole mechanism;
  • The broken design is removed with a screwdriver, changes to the new one.

All work is almost completed. But since we all disassembled, changed the necessary components, now you need to build a design and install back to the car.

Causes of mirror breakdown

The most common occasion for replacing the rear-view mirrors can be called cracks as a result of shocks. First of all, it concerns the external elements of the review, since they are most often interfere with the movement of other road users. In most cases, it is possible to avoid both external and internal damage to the side mirrors by installing a special decorative film. However, this method will be able to help not always. Especially when it comes to strong impact. Another reason for the replacement of external mirrors is the deformation of the cables. To establish new cables, you will have to fully disassemble the item.

We recommend reading

  • Adjusting the side mirrors of the car
  • Salon rearview mirror - improve car visibility
  • Automotive mirrors - customize and repair

Internal mirrors also fail. In most cases, the breakdown is the result of frequent parts adjustments. At the same time, re-setting the element, the driver does not even suspect damage.

In fact, it is necessary to start repairing the mirror and try to disassemble it already when the item at least a little dismissed from the situation given earlier. If this happened, it means that the fasteners are shifted. They often completely dug and the driver can notice it only looking at the windshield outside the car.

Common device malfunctions

Consider a few troubles that every car enthusiast may encounter.

Out of a mirror surface

Sometimes this trouble occurs even on new cars. Causes can be the most different.

  • The manufacturer decided to save and used low-quality adhesive composition;
  • During the work, the master did not allow glue to be captured;
  • The mirror was broken due to too sharp temperature differences (and this is the most common cause, especially frosty winter).

In all these cases, the car owner will have to use two-component glue, as shown above.

Procedure for replacing glass

The mirror element of both an outer and salon mirror may be damaged. Below is the sequence of its replacement:

  1. Glass is extracted from the mirror body.
  2. The new mirror element has several plastic hooks (in our example 4). These hooks are introduced into the fastening holes in the mirror body, after which it takes very gently to press on the mirror element.

    The new mirror element is installed in the mirror housing manually

  3. The characteristic click, saying that the plastic hooks joined and the glass "village" in place.

The procedure for replacing the mirror elements in the salon mirrors is similar to the one that is given above (the only difference is plastic latches in the salon mirror, as a rule, 2, and not 4).

The rear view mirrors are able to deliver a lot of trouble by car owners. But fortunately, most of these problems are solved on their own. Removal and securing the mirror element can be performed on their own. The main thing is to act as careful and not forget that the glass is an extremely fragile material.

Repair of the mirror of the rear view - how to make out your own hands? +.

how to remove the side mirror

It often happens that the fastening of the rear-view mirror is weakening, and the mirror holds poorly or disappears (perhaps someone hooked him on the go). It happens that the side mirror crashed or gave a crack - it needs to be changed. It may be necessary to repair the drive adjustment of the mirror.

You can contact the car service, and the mirror is attached to the place. But if there is no room nearby, you will have to act independently.

The rear view mirror is extremely important on the road: the driver can follow the situation on the roadway in the review area behind the posterior wings and rear bumper.

Mirrors on different brands of cars are different: an inner mirror and side mirrors, conventional, folding, with electric and others. When removing and disassembling any mirror you need to be extremely neat so as not to damage the mirror itself.

What will be required for disassembly

In order to disassemble the mirror, you will need a tool:

• 2 flat screwdrivers (latches are packed).

• Thin long screwdriver and a piece of soft tissue (in order to wrap a screwdriver).

• Key-star to 10 or a regular replaceable bits screwdriver.

Attention! For disassembly of one mirror can leave for 15-20 minutes.

How to remove the mirror

how Dismantle the side mirror with electric drive (Assembly):

one. With the front door remove the triangular lining.

2. Swede connector wiring mirrors. Do not damage the wiring of the mirror heating!

3. Holding the mirror, turn out 3 mounting screws.

four. Remove the mirror assembly.

five. Installation of mirrors We produce in the reverse order.

Disassembling the side mirror of the rear view with a mechanical drive:

one. Remove the lock bracket of the mirror regulator.

2. Holding the mirror, turn out 3 mounting screws.

3. Remove the mirror.

four. Installation is carried out in reverse order.

How to remove the rear view mirror in the cabin car

The most common option to fasten the rear view mirror on the windshield - 2 bolts. Such fasteners are found on domestic machines. To remove the mirror in the cabin, act as the following order:

one. Remove the plugs on the bolts (if any).

2. Holding the mirror, unscrew the fastening bolts.

3. Remove the mirror.

four. Place of adjustment of the mirror to the windshield wipe with alcohol.

five. When installing the mirror, you need to trace the mirror "village" to the same place (Piglet on the windshield).

On a foreign car, the rear view mirror is glued to the windshield. To remove the mirror from the windshield, make such actions:

one. We remove all plastic plugs with your hands.

2. Moderately pull the mirror up (to the ceiling).

Attention! Follow the condition of the glued fastener. If everything is done correctly, the mirror will remain in the hands, and the bracket (it is not removed) - on the spot.

Properly apply power (when you pull the mirror up). If you overdo it, the windshield can crack. If the mirror has already descended from the place of the bracket), and you still pull it with it, you can accidentally sharpen the upholstery on the ceiling. On some models, the car is a special retainer in the form of a button (you should click on it).

How to disassemble a mirror, 2 ways

To make a replacement of a cracked mirror, you need to know how to disassemble the rear view mirror. You can only remove the mirror: it is convenient, and safely for the mirror itself. Rear view mirror can be carried out in two ways:

• After after removing the mirror from the door or windshield. This method of disassembly is safer for the entire mirror block.

• Disassemble the mirror without dismantling it from the place of attachment.

Attention! Without skills, this disassembly is not recommended to do. The disassembly of the side mirror of the rear view is quite feasible. But disassemble the mirror on the windshield is extremely undesirable: any clumsy action screwdriver - and the crack on the windshield is provided.

If you need to replace any element of the mirroring unit, the analysis of the rearview mirror is to be done. Fully disassemble the rearview mirror (lateral or from the windshield) can be acting according to the scheme:

one. Hairdryer warm the mirror housing (warm glue on which the mirror holds, softens, and it will make it easier).

Recommended: Top 10 brake pads

2. Wooden blade or wrapped in a soft fabric flat screwdriver are trying to separate the mirror itself from the case. To do this, carefully (up-down) we upgrade the mirror with a thin tool.

3. Now disconnect the heating wires of the mirror (2 them).

four. There are 3 bolts on the adjustment mechanism. They need to unscrew.

five. Disconnect the wires from the adjustment mechanism.

6. We postpone the adjustment mechanism. Under the mechanism are fasteners.

7. First remove the rear top cover. Cover mounts are made in the form of the tongue. They need to be pressed towards each other. On the right side, the tongue needs to be pressed to the side (repel it out).

8. Slowly and neatly pull the lid on yourself.

9. Now disconnect the rear bottom cover. There is also a fastening tongue here. Press the tongue with a screwdriver and simultaneously with a knife (or flat screwdriver) push the tongue from the back cover.

ten. Gently disconnect the back cover. For the attachment of the rear-view mirrors, it is better to use chemical hardening glue.

Rules of repair

Repair Rules Repair Mirrors are the same for all kinds of mirrors:

• Repair of the mirror is better to exercise, after removing it from fasteners.

• The disassembly of the mirrors is safer in the removed form.

• Before picking up and pulling the mirror itself, warm the body with a hairdryer.

• Do not press with a lot of effort on the mirror - it can give a crack.

• Be extremely accurate when removing the mirror from the windshield (you can break the windshield or damage the upholstery on the cabin ceiling).

• Do not make sudden movements when disassembling the mirror block (you can break the heating wires).

• If it is impossible to replace the broken part of the mirror block, you will have to put a new mirror block.

Did you know? To glue the falling mirror in place, you first need to remove the remaining old layer of glue. But before that, outside the windshield, make the marker label (the mirror should sit in its place).

A source: https://avto-idea.ru/remont/remont-zerkala-zadnego-vida-kak-razobrat-svoimi-rukami/

Independently change the rearview mirror

how to remove the side mirror

Any car enthusiast will not ride without a mirror of the rear view. But this simple device fails. Fastening the salon mirror sometimes suddenly weakens. And the external mirror someone can hurt and accidentally smash. In addition, an angle adjustment drive is periodically breaking in the mirror. Is it possible to solve all these problems yourself? Of course: to disassemble, remove or glue the mirror yourself for most car enthusiasts. It is not as difficult as it seems.

Removing the outer and inner rearview mirrors

Rear view mirrors are an integral part of the car. Even those drivers who equip their "swallow" with a monitor or camera cannot do without mirrors. Therefore, keep them in good condition - the first task of each car owner. Before switching to the procedure for disassembling mirrors, list the toolkit that we need to work.

Required to dismantle tools

  • shirling cross;
  • Shutter with flat sting.

How to disassemble an external mirror

Disassembly of outer mirrors expediently implement in a certain sequence.

  1. Using a screwdriver removed the locking bracket, to which the adjustment of the angle of the mirror of the mirror is attached. The side mirror bracket is extracted with the help of a crossover
  2. The same dummy turns the mounting screws. There are only three of them. During the extraction of these screws, the mirror must necessarily hold. Self-tapping screws holding a side mirror, unscrew the crossed scold
  3. After removing the screws, the mirror is removed. To do this, it needs to be slightly pulled at himself. After extracting self-removal mirrors, manually removed

How to remove the salon mirror

Change the rear view mirror in the cabin is a bit more complicated. Works need to be carried out in such a sequence:

  1. Plastic plugs over the fastening screws of the salon mirror are neatly approaching a flat scolder and removed.
  2. Fastening screws are unscrewed by the cross scolder. The main screws of the salon mirror are twisted with the cross scolder
  3. The mirror is neatly removed.

How to spare the mirror from the windshield

Conducting a dismantling of the glued mirror does not require special skills. Act as follows:

  1. In some modern cars, the bracket with the cabin mirror is glued straight to the windshield. To remove it, you must remove all plastic plugs from the bracket (if any).
  2. After that, the mirror turns the two hands counterclockwise and removed from the nest. The filled mirror turns 90 degrees and is removed manually

Disassembly of rearview mirrors

The procedure below is used for both external and internal mirrors.

  1. The mirror is removed from his regular place.
  2. Hand should be gently pressed on the top edge of the mirror glass until it turns out. The sideline element of the side mirror turns manually
  3. In the slot, which occurred between the mirror body and glass is placed a piece of a vet or a napkin.
  4. Then a flat spun, pre-wrapped with a tape, which holds the mirror element, is acknowledged into this slit.
  5. Lockers holding the mirror are subject to scolding and removed from the protrusions.
  6. Mirror glass is carefully removed.

The left mirror is dismantled in the same way as the right.

How to glue the cabin mirror to the windshield

To begin with, decide on the glue that we are going to use.

What glue you need to use

The main rule: the glue holding the cabin mirror on the windshield must be two-component. Yes, there are many varieties of universal glue. But in this case, the universal glue is not suitable. The fact is that two-component glue perfectly withstands harsh temperature differences, high humidity, and most importantly - vibration. Conclusion: The mirror element should not be glued to universal glue.

There is a second option: use the light-cured glue. This substance that is quickly "grasped" under the influence of sunlight. Such glue can be purchased in specialized auto shops.

But he has a serious minus: there is a powerful ultraviolet lamp to work with it, without which the reliable gluing is not achieved.

Some car enthusiasts claim that it is possible to do without it, it is enough to just glue the mirror with a sunny summer day. But it is impossible to name such a gluing.

The output is simple: the best and least troublesome option for gluing the mirror is two-component glue. For example, Loctite 37438, which has recently become incredibly popular. By the way, it is sometimes used to glue from video recorders, which weakened the fastener device.

How to fix the mirror element

So that the mirror holds reliably on the windshield, it is necessary to act according to the following algorithm:

  1. Selects the place of installation of the mirror. It must be glued in the center of the glass, at the same distance from both the passenger and the driver.
  2. The windshield is cleared of contamination. Initially, this is done with the help of a vet, then the glass surface is cleaned with alcohol.
  3. The mirror disassembles as indicated above (after all, in fact, only the bracket on which the mirror will be installed) should be glued to the glass.
  4. The thin layer of adhesive is applied to the bracket and on the windshield. After that, you need to wait at least 15 seconds. The bracket of the salon mirror is applied glue
  5. The bracket is then installed on the windshield and slightly pressed manually (and if it is decided to install the mirror completely, without disassembly, then after installing it, it is necessary to further fix the scotch, which will support the mirror until the glue is grabbing). The alphabet
  6. The glue should dry, so that during the day it is impossible to ride the car.

Installing a device on a bolted mount bracket

Not on all modern cars, salon mirrors are glued to the windshield. In some cases, the mirror bracket is attached in the old manner: bolts to the ceiling. In this case, you need to act like this:

  1. The mirror together with the mounting bracket is installed in the ceiling niche and sticks with the hand. The alone mirror is installed in a niche and sticks with hand
  2. The screws are inserted into the holes and tweaked with the help of a crossover.
  3. The sockets with installed screws are closed with plastic plugs (provided that those are provided in the bracket design).

: About the brake controller sorcerer

How to install and fix side mirrors heated

To make yourself assembled and connect side mirrors, you will need minimal knowledge in the electrician and skill. It is necessary to act in such a sequence:

  1. A set of mirrors equipped with an internal heating system was purchased. Heated with heated for Lada Grant car
  2. From the car removed the regular side mirrors in the way that was mentioned above.
  3. After installation, the top cover on the body of the side mirror opens. Access to the wiring connections jack (it is supplied with mirrors). Outputs the side mirror housing and connects electrical wiring
  4. The wires are connected to the socket and through the mirror housing are at the door.
  5. With the door of the crosst hole, plastic cover is removed. The door of the car removed the plastic cover
  6. Wiring is pulled through the door and dashboard to the fuse block, next to which the relay is with a plug to turn on the heating of mirrors. Conducting mirrors connects to the heating relay
  7. The posting plug is connected to the jack shown in the photo, after which the vehicle's door taking reverse assembly is made.

Common device malfunctions

Consider a few troubles that every car enthusiast may encounter.

Out of a mirror surface

Sometimes this trouble occurs even on new cars. Causes can be the most different.

  • The manufacturer decided to save and used low-quality adhesive composition;
  • During the work, the master did not allow glue to be captured;
  • The mirror was broken due to too sharp temperature differences (and this is the most common cause, especially frosty winter).

In all these cases, the car owner will have to use two-component glue, as shown above.

Procedure for replacing glass

The mirror element of both an outer and salon mirror may be damaged. Below is the sequence of its replacement:

  1. Glass is extracted from the mirror body.
  2. The new mirror element has several plastic hooks (in our example 4). These hooks are introduced into the fasteners in the mirror housing, after which it takes a very gentially pressing on the mirror element. One mirror element is installed in the mirror housing manually
  3. The characteristic click, saying that the plastic hooks joined and the glass "village" in place.

The procedure for replacing the mirror elements in the salon mirrors is similar to the one that is given above (the only difference is plastic latches in the salon mirror, as a rule, 2, and not 4).

how to assemble and change the mirror element

The rear view mirrors are able to deliver a lot of trouble by car owners. But fortunately, most of these problems are solved on their own. Removal and securing the mirror element can be performed on their own. The main thing is to act as careful and not forget that the glass is an extremely fragile material.

Copywriter with five-year experience.

A source: https://auto-gl.ru/samostoyatel-no-menyaem-zerkalo-zadnego-vida/

How to remove and disassemble the rearview mirror and how to stick it into place

how to remove the side mirror

The circumstances at which you need to dismantle the rear-view mirrors can be diverse. For example, repairing or replacing a cracked glass, buying new modified models and even ordinary braid tinting.

In addition, you can install the heater, as well as the monitor and the rear view chamber. Remove the damaged mirror, disassemble it and glue the new one with your own hands is not as difficult, as well as install the devices more comfortable reflector.

To do this, arise the manual for the operation of its car and our instructions.

Mirrors of this type are designed to explore the situation on the road behind the car. You can divide them into two categories:

  • Salon - installed inside the car;
  • Side - located on both sides on the front door racks.

Salon mirror is located inside the car

Side mirrors are located on both sides of the car

It seems that it may be easier to dismantle the mirror? In fact, this is not so easy, moreover, the principle of dismantling in various brands and models can vary significantly. We will tell about the most universal ways to remove, parsing and installing internal and external.

However, if any of the methods described here is not suitable, look at the instruction manual for your car.

Today, many car firms greatly facilitate all similar processes: possibly, instead of unscrew the bolts and flexing the terminals, you will only need to press a small button or pedal.

In order to remove the mirror, you will not need any specific and hard-to-reach tools. As a rule, everything you need in the garage at any motorist.

  • Set of screwdrivers (will be suitable, most likely, only figure and flat);
  • wrench depending on the size of the bolts;
  • Household hair dryer for removing the mirror element.

Add to this set skillful hands and the desire to do everything qualitatively, and you can proceed.

Salon

Internal mirrors can be installed in various ways depending on the brand, model and year of production of the car. There are two ways that apply most often.

  1. Installation in the ceiling of the car with bolts or screws.
  2. On the windshield with a glue or suction cup.

So, on many domestic cars, the helper device is installed using conventional bolts, which significantly simplifies the dismounting process. To do this, you just need to unscrew the bolts, after removing the plug.

In order to remove such a mirror, you just need to unscrew the bolts

The situation may become more complicated if the mirror is installed on the bracket glued to the glass. First of all, check if there is an opportunity to divide the bracket itself and the platform glued to the glass. On most cars, they are separated by moving the clamps or turn to a certain side.

If the mirror is glued to the glass, you need to try to separate the bracket from the holder platform

If there is no such possibility, you will have to resort to the radical method and remove the bracket along with the windshield. The fact is that the glue holds the elements very firmly, so when trying to separate the mirror, you can accidentally damage the glass.

Before starting this process, look into your guide to your car: it should describe in detail the process of dismantling some elements. Remember that the purchase of new windshield will cost you weekly.

Alone to separate the platform of the bracket from the mirror you, most likely, will not work, so it is better not to risk and contact a special interior. Moreover, if you disassemble for the sake of future tinting. However, if you still decided to do it yourself, be prepared that the mark will remain on the glass from the glue.

Side left and right

Side mirrors are divided into two categories:

  • with mechanical drive;
  • with electric drive.

Almost all cars to get to fastening screws, you will need to remove the door trim. Learn how it can be done on your model, you can from the instruction manual.

So looks like a car door with a lifting

Next, to remove the part with a mechanical drive, you need to perform a specific procedure.

  1. Remove the lock bracket of the regulator.
  2. Unscrew the mounting screws on the inside of the door.
  3. Remove the mirror.

Dismantling side mirror

If the mirrors have an electric drive, the procedure will be slightly different.

  1. Disconnect the minus terminal from the battery.
  2. Disconnect the shoe with wires.
  3. Unscrew the mounting screws on the inside of the door
  4. Remove.

Side

After you have separated the side mirror body from the car body, it should be disassembled. First of all, you need to remove the mirror element. This process may not coincide in various brands, however, the next procedure is most often applied.

  1. An ordinary household hairdryer thoroughly warm the place of connection of the reflective element with the case. The temperature of the air flow should not be too high, so the technical hair dryer does not fit here.
  2. Using a dumping with a straight slot or a small spatula, separate the mirror from the case. On some models at this stage you need to bend terminals. In order not to damage the glass, the dumping or blade can be wrapped with a tape or soft cloth.
  3. In some designs, to separate it, you need to slightly press it in the center and how to put forward. After that, the reflective element can be removed with neat movements.
  4. Then unscrew the central screw with the plastic frame (if available).
  5. Under the frame there are all the mechanisms of the side mirror. With the help of a screwdriver, you can unscrew any of them and put in place. You can independently divide the design to all components, including adjustment and folding engines.

The process of disassembling the side mirror

The mirror is assembled in the same way, but in reverse order.

How to fix and how to glue a new

If you have successfully dismantled the mirror yourself, then return it back will not be any difficulty. As a rule, all actions are performed in the reverse order.

But the selection of glue is worth paying special attention, since not everyone will suit this process.

It is necessary to choose the right glue for fastening the mirror to the windshield

Selection of glue

There are three types of compounds for gluing mirrors:

  • chemically curable;
  • Light-cured;
  • Epoxy resin-based compounds.

The composition with the resins will only affect if they give it to dry. Usually it takes from 10 hours to days. In this case, the part must be tightly pressed all the time. Such an approach is not very convenient, so such money does not apply in everyday life.

Light-cured mixtures act when exposed to special ultraviolet lamps. This is one of the most common techniques in production. However, if you are not a happy lamp owner, it is not worth purchasing such a composition. Sunlight, especially scattered, is not able to have sufficient influence.

For these reasons, chemically curable compositions enjoy the greatest popularity. A special hardener launches the polymerization process. As a rule, they consist of glue itself and an aerosol activator, although one-component compositions are found.

Please note that some materials cannot be used to glue the mirror.

  • household superchalters;
  • Bilateral adhesive tape.

The adhesive component of both materials has such a composition that, when used on glass or metal, it will not be able to frozen completely. The high temperature of the air inside the cabin or heating the glass from the sun rays soften it, and the mirror will disappear. You can use household adhesives only if the mirror fell completely unexpectedly, and now you need to get to the car service.

I tried three times on the superclas. I confirm: no more than a week holds.

Max

A source: https://carnovato.ru/kak-razobrat-zerkalo-zadnego-vida/

How to remove and disassemble the side mirror of the rear view of the car: instruction

Rear view mirrors - an integral attribute of any car. They may differ in size, forms and functionality, but they are all intended for one - so that the driver can control the situation around his car.

A rather common problem is a breakdown of the side mirrors of the rear view. Often it happens in the parking lot. When the driver is not near, the parking "neighbor" may accidentally knock the rear-view mirror, if it is damaged, it will be necessary to remove it and install a new one in its place. But this is not the only situation when it may take to remove the side mirror of the car. For example, this work is to be fulfilled, if you wish to repaint it or simply replace.

Consider within the framework of this article, how to remove and replace the side mirror of the rear view by car.

1. How to remove the side mirror of the rear view 2. How to disassemble the side mirror of the car

Please note: the Instructions below will show general tips on the dismantling of the mirror. Depending on the car model and the mirror design, the instruction may differ slightly.

How to remove the side mirror of the rear view

The side mirror of the rear view in a modern car is a real "gadget", which built various additional accessories. Among them: repeaters of turns, LEDs, heating elements, and so on. Accordingly, before switching to the removal of the mirror, you need to reset the minus terminal with the battery to minimize the risk of a short circuit during operation.

After that, go directly to the dismantling of the mirror according to the following scheme:

  1. Open the car door;
  2. Remove the mirror angle change handle. Most often for this, it is enough to pull it on itself, after which it will come out of the grooves and will take off. But on some car models, this may occur otherwise, for example, it may be necessary to unscrew the clockwise or first remove the fastening bolts;
  3. Next to remove the mirror you need to find bolts from it and unscrew them. Most often bolts and fastening elements are hidden from eyes under a decorative plastic overlay. Find it and carefully remove with a flat screwdriver. It is important to note that together with the lining there is a rubber element-gasket. Do not lose it because it is almost impossible to purchase them;
  4. When the bolts are visible (most often they are from 2 to 4 pieces), unscrew them;
  5. Follow the bolts from the mirror turning mechanism. It is also fixed on bolts, most often of them 2 or 3. Be sure to take a picture of the location of the multi-colored cables that go from the rotary mechanism to the mirror to remember their location and do not wash anything when assembling.

Important: If the position of the side mirrors is adjusted using an electrical drive, it will also be necessary to disable the corresponding wires.

How to disassemble lateral car mirror

The discoulding the side mirror implies the removal of the mirror element directly, which is located in a plastic case. This is necessary if the mirror element crashed, you need to repaint a plastic element or make some other manipulations with these parts separately from each other.

A mirror element is fixed in the housing of the mirror using several plastic latches, which are located from the opposite side. Most often such latches about 8 pieces, 2-3 on each side. We recommend to act as follows to pull the mirror from the case and at the same time do not damage any of the items:

  1. Since plastic latches, it makes sense to heat them a little so that they are more fuel to deformation. To do this, you can use the usual household hair dryer. Direct it for 3-4 minutes on the glass, it is desirable evenly distributed heat across all edges of the mirror. IMPORTANT: Do not use the construction hairdryer for this work, since its temperature may exceed the melting point of the plastic, as a result of which the mounts and the side mirrors are deformed and spoiled ;
  2. When the latches have become softer, you can move directly to the mirror removal process. To do this, we recommend to take plastic blades (which are often used in mobile engineering services). If there is no such shovel, you can use a conventional flat screwdriver, but before it is desirable to wind the electrical parts, it is necessary to accidentally not scratch the mirror and the case. Also get a small piece of soft tissue;
  3. After that, put a soft piece of fabric to the plastic part of the case in a place where you will encourage blades or screwdriver. After that, insert the tool, thereby moving the mirror;
  4. Next, carefully pull the improvised lever from the screwdriver or the blade to remove the mirror element from plastic mounting or fasteners;
  5. Freed one side of the fasteners, do similar activities with others;
  6. After that, carefully remove the mirror, but note that it can be even attached to anything, for example, on glue, or wires can go to it. Disconnect everything too much and get the mirror element, on which the process of parsing the side mirror can be considered complete.

Depending on the model of the car and the mirror used, the space under the mirror element can be empty or filled with various components. Their disassembly, if necessary, should not cause difficulties.

(421. vote., 4,53. out of 5)

A source: https://okeydrive.ru/kak-snyat-i-razobrat-bokovoe-zerkalo-zadnego-vida/

How to disassemble lateral mirrors? 4 ways - Chini car!

Any car enthusiast will not ride without a mirror of the rear view. But this simple device fails. Fastening the salon mirror sometimes suddenly weakens. And the external mirror someone can hurt and accidentally smash.

In addition, an angle adjustment drive is periodically breaking in the mirror. Is it possible to solve all these problems yourself? Of course: to disassemble, remove or glue the mirror yourself for most car enthusiasts. It is not as difficult as it seems.

How to disassemble the side mirror - auto-repair

Super User 1 Details Category: Uncategorised: 03 May 2017 2232

When there is a need to disassemble the automotive mirror (and there are many reasons for this), then this is often accompanied by certain difficulties.

The designs of the mirrors are the most different: heated, with an electrically regulating, self-skewed, with built-in repeaters of rotary lights. The main thing after dismantling the mirror and disassembly does not damage the components of the structure.

For this, all actions need to be performed extremely gently and consistently, otherwise this car body element will have to be replaced.

Below you are offered general information about the disassembly process of the mirrors. Adhere to these recommendations, and you will never worry the question again: "How to disassemble a car mirror?"

Dismantling of the mirror

There are certain differences in the dismantling of the mirror with a mechanical drive and with an electric drive. In the first case, the disassembly process consists of such steps:

1. Dismantling of the retaining bracket and regulator.2. Dismantling the fixture fastening screw, which holds the mirror on the frame.

3. Dismantling directly the element itself.

Removing the automotive electric drive mirror is performed as follows:

1. First, the "minus wire" is disconnected from the battery.2. Share, separated terminal block (hermetic) with electrical drive wires.

3. The final step is to unscrew the screws securing the mirror to the car door.

Methods for extracting a mirror element

A car mirror is dismantled in different ways.

Option number 1

Using a screwdriver or a sharp object with a curved tip gently pressing on the mirror element from the inside. This dismantling method requires extremely accurate movements so as not to damage the mirror element itself. The experienced motorists when dismantling the mirror on this method are wrapped the edge of the puller insulating tape. Thus, there are no scratches on the mirror surface.

You can also apply two mounting blades, one - to fix the slot between the body and the mirror, the second - leash the mirror from the frame.

Option number 2.

To quickly remove the mirror, the case hits a soft surface. This dismantling method will prevent damage to the mirror and will avoid additional difficulties. But first, you need to disconnect the car mirror body itself from the triangular fastening on the car body. First of all, the spring is extracted, and then adjusting thrust. After extracting the main attachment in the form of a pin, you can proceed to further disassembly of the structure itself.

Universal dismantling option

The universal method of removing the mirror is most practical. The process consists of the following actions:

1. The pad is retrieved, hiding the mirror mounting screws from the car's salon.2. Screws, fixing the mirror, are unscrewed, after which the entire design is removed. Rubber seals are extracted. It is extremely important not to damage the gaskets, they are not so easy to find them in case of replacement. They are quite rarely sold separately.

The screw is unscrewed, fastening the joystick setting the mirror element. At this stage you need to be very attentive. Be sure to memorize the arrangements of the cables, they have different colors, and each is responsible for a specific direction during adjustment.

5. 3 screws in the lower corner are unscrewed.

You need to unscrew them very carefully, so as not to harm the design.

After performing all 5 stages, you can move to the removal of the mirror element. How it is done - indicated above.

If it is necessary to remove the mirror, it is still better to contact a professional master or perform this manipulation in the automotive service. But if you are used to independently repair your car, then our recommendations for dismantling the mirrors will probably become useful. In addition, the prompts provided will save your budget.

A source: https://555-shop.ru/remont/kak-razobrat-zerkalo-bokovogo-vida.html

Replacing the rear view mirror with their own hands: how to remove, disassemble and glue a new

The circumstances at which you need to dismantle the rear-view mirrors can be diverse. For example, repairing or replacing a cracked glass, buying new modified models and even ordinary braid tinting.

In addition, you can install the heater, as well as the monitor and the rear view chamber. Remove the damaged mirror, disassemble it and glue the new one with your own hands is not as difficult, as well as install the devices more comfortable reflector.

To do this, arise the manual for the operation of its car and our instructions.

How to remove the rearview mirror

Mirrors of this type are designed to explore the situation on the road behind the car. You can divide them into two categories:

  • Salon - installed inside the car;
  • Side - located on both sides on the front door racks.

Salon mirror is located inside the car

Side mirrors are located on both sides of the car

It seems that it may be easier to dismantle the mirror? In fact, this is not so easy, moreover, the principle of dismantling in various brands and models can vary significantly. We will tell about the most universal ways to remove, parsing and installing internal and external.

However, if any of the methods described here is not suitable, look at the instruction manual for your car.

Today, many car firms greatly facilitate all similar processes: possibly, instead of unscrew the bolts and flexing the terminals, you will only need to press a small button or pedal.

Required tools

In order to remove the mirror, you will not need any specific and hard-to-reach tools. As a rule, everything you need in the garage at any motorist.

  • Set of screwdrivers (will be suitable, most likely, only figure and flat);
  • wrench depending on the size of the bolts;
  • Household hair dryer for removing the mirror element.

Add to this set skillful hands and the desire to do everything qualitatively, and you can proceed.

How to correctly disassemble the side mirror of the rear view?

Rear view mirror is necessary for each car. They are not the same on different models of machines, but perform the only function - expand the driver's horizon.

Unfortunately, a breakdown of these elements of the car becomes a frequent problem. This part of the car on the car park is most vulnerable. Any "neighbor" may accidentally knock the mirror. Unfortunately, when a breakdown of this kind, only one exit is to remove the damaged part and install a new one instead. However, such a sad situation is not the only reason for changing the mirror. This skill will be required during repainting a car or if the mirror surface of the scratched or cracked.

Side rearview mirror

How to remove the side mirror of the rear view with their own hands

This accessory is not so simple as it seems. Most often, various devices are built into it. For example: turn repeaters, LEDs, heating parts. For this reason, before removing the mirror, it is necessary to reset the negative charge from the battery. It is necessary in order to minimize the likelihood of a short circuit during the work.

Replacing the side mirror of the rear view

Tools that will be required for this repair will be found in every garage. These include: a set of screwdrivers of different sizes, household hair dryer, plastic blade, tape, small piece of soft tissue, wrench. In addition, attention will be useful to detail, caution and desire to do everything correctly.

Removal process. After a negative charge is reset from the car battery. You can proceed to dismantling. To do this, open the car door, remove the handle of the change of the corner of the mirror.

The process of removing the correction handle of the angle varies on separate models of cars. For example, on some, it is enough to pull the handle for yourself in order to come out of the grooves. On other models it will have to get out counterclockwise or, before removing, you will need to unscrew the bolts on which it holds.

In order to remove the mirror, you need to find bolts that hold it. As a rule, they are under the decorative lining and are located so that they would not be seen. The decorative hiding element needs to be removed. Often together in it removes a rubber gasket.

It is important not to lose it due to the fact that these elements are not sold in stores separately, except for some exceptions. When the hiding pad is removed, the bolts are clearly visible.

They need to be unscrew in addition, to avoid confusion when assembling, it is best to photograph the location of multi-colored wires.

How to disassemble lateral rearview mirror

This will be required if, for example, the mirror element crashed and need to be replaced. It is fixed in the case of plastic latches. As a rule, they are from the reverse side of the mirror surface. The amount of attachment data is different on various models of cars.

In order for plastic fasteners more controlled, you need to warm them. This can help a regular hairdryer. The jet of warm air needs to be directed to the entire surface of the glass. Usually there is enough pair of minutes. In addition to the usual, household hair dryer, there is a construction. However, this operation is better not to be carried out with it.

The fact is that the latter can heat plastic to melting point and damage fasteners.

When latches from the heat become softer, you need to take plastic blades or a flat screwdriver. Use a metal object, you must extremely carefully, it can scratch the glass or body. The lever method you need to dig a mirror from fasteners. Bloxt attachments are not the only thing that connects the mirror with the case. In addition to them, there may be glue or wires. You need to disconnect all unnecessary elements.

It is easier to put a mirror surface back much - you just need to combine the latches in the desired order and put pressure on the surface of the mirror.

Useful advice

Under the blade or screwdriver you need to put a small flap of soft tissue, it will help to avoid damage to the outer part of the mirror.

When removing the mirror surface with a screwdriver fasteners, it needs to be cooled. So the risk of damage to the remaining elements is reduced.

Side rearview mirror

If the mirror was attached to the glue including, it is necessary to return this layer. It is important to use the correct, suitable glue. For these purposes, there are three varieties: chemically hardened, light-subsidized, epoxy compositions.

The latter will act as it should only be dry. In other words, the item must be pressed in the right state for ten o'clock. Light-cured adhesive mixtures should be exposed to ultraviolet. For it, the lamp will be required, solar light is not enough.

The glue mixture is perfectly suitable, which has the ability to harden with the help of chemical processes.

In no case cannot be used by the usual superal and adhesive tape. These funds do not have the desired properties, and the mirror will definitely fall over time.

A source: https://smotriavto.ru/obsluzhivanie-i-remont/bokovoe-zerkalo-zadnego-vida.html

How to disassemble the side mirror of the rear view - how to remove and attach a new

Hello everyone! I think there are many different reasons due to which the driver may need to replace the rearview mirror. Someone cracked the glass, the housing itself broke away from others. Or the car owner just wanted to put a more modern design or toned glass.

And maybe you have blocked the light bulb in the mirror, and therefore you will have to disassemble everything first, and it is again.

Now there are many options for new glasses that come to replace the regular mirror.

The same feature of the rear view camera, heating or monitor may not be at all extra in the car.

The essence you caught. We need to remove, disassemble and back to install the mirror. What kind of? Logical question. Procedures can concern both the outer mirror and what is in the cabin. Accordingly, we will talk separately on the topic of the left and right side mirror, as well as the inner salon.

Why remove the mirror from the windshield

Side mirrors Auto may need to remove to, for example, replace the glass on them, or in the case when the electric drive breakage occurred.

It is worth noting that it is necessary to do this as careful as possible, because this is part of the body whose damage will worsen the appearance of the car.

It is best to entrust such a procedure to professionals, then you can confident that everything is correctly secured, and the paintwork will remain without damage. At least, the car service will take responsibility for the quality of repair on itself.

Even taking into account the fact that removing the side mirrors is quite simple, although in different brands of the car, the sequence of actions may vary, independent dismantle can lead to damage to the electronics.

As for the rearview mirror in the cabin, here you can often stumble upon the driver's question, how to remove it from the windshield without the help of the car service? Consider what the need for such actions may arise:

  • It may take to replace the broken glass or repair the electronics;
  • In case the mirror is mounted not tight, sounds and vibrations may occur while driving;
  • If you want to toned the windshield (remember that according to GOST, the toning cannot exceed 25%);
  • Upgrade mirrors, such as rear view camera with parking sensors;
  • Installation in the area of ​​the rear view mirror of any devices and sensors that are not provided for in the car package.

Recommended

"Where to change the windshield: signs of high-quality service" More details for many motorists, the process of such dismantling causes difficulties that it is not surprising, because to break the mirror, damage the ceiling or smash the windshield to anyone you do not want. At the same time, there are a number of practical recommendations that will help to properly conduct this procedure.

How to remove the mirror from the windshield on the domestic car

The cars of the Russian auto industry, produced until 2009, did not differ in complex innovative solutions in the field of fasteners. Therefore, here the owners are lucky - unscrew two bolts and remove the item, most likely, no work will be.

You can offer a simple algorithm for dismantling the salon mirror from the windshield in the domestic car:

  • On bolts you need to remove the plugs (or skip this step if there are no plugs);
  • one hand hold the mirror so that it does not fall, the other does not rush to unscrew the bolts;
  • Remove the mirror from the windshield and degrease the place of its attachment, such as alcohol.

Then, when the necessary repair or modernization will be produced, it is necessary to attach everything into place. To do this, you just need to fasten the bolts and put plastic plugs on them. It is important that the location of the Piglet on the windshield has not changed after all manipulations. As you can see, in the case of Lada brand cars, there are no problems of self-removing mirror from the windshield.

How to remove the mirror from the windshield in foreign cars

Is everything so easy with foreign cars? Let's try to figure out.

In fact, when removing the mirror from the windshield in foreign production machines, a number of problems may really occur, the largest of which is the risk of damaging the windshield itself.

The fact is that in foreign cars, in order to dismantle the mirror in the cabin, you need to attach a lot of effort, at the same time, the lobovik is not designed for excessive pressure, and, if you move, it simply simply can go cracks.

How to try to remove the mirror mount from the windshield on your own

Applying coarse male strength, in order to remove the fastenings of the rear-view mirror in the cabin, you can break the windshield with a lacaround.

It is best to carry out a dismantling procedure not alone, as well as use a construction hairdryer, pliers and clean dry tissue.

Ask someone to help you, not need to have special qualifications in this matter. Just someone has to warm the windshield in the area of ​​Piglet with circular movements, and you, meanwhile, neatly pliers try to move the mount from the place, siping it from the side to the side.

It is a construction hairdryer that needs to be used for this purpose because the heating temperature should be 300-350 degrees Celsius, the usual household hair dryer will not be able to provide. When you feel that the Piglet is about to take off, prepare the fabric to catch it, as it will warm up from the hair dryer too.

After dismantling, be sure to wipe the place of fastening with alcohol, upload, if necessary, and, using special glue, glue five.

And yet we will remind you if you doubt whether you will have to independently carry out all the above manipulations, contact a service center, where the risks associated with the repair of the car will take a specialist. After all, it often happens that the repair in its garage will cost even more expensive, and the consequences of this repair will be difficult to correct.

At a minimum, first examine the instructions from the manufacturer of your car. It will not be superfluous to consult a professional or on a specialized forum.

A source: https://automanya.ru/sovety/zamena-zerkala-Bokovo-Vida.html.

Добавить комментарий