How to sew a fur hat with their own hands - my fur coat

In winter it is very important to wear a headdress. In particular, the inhabitants of cold regions are needed warm and dispropal protection for the head. The ideal option will be fur hat . And it is not necessary to run for her to the store. The homemade hat, the so-called hand-made, will make your headdress not only functional, but also unique. We give for you, needlewomen, three examples of how to sew a hat from fur with their own hands.

Stylish fur hat in the form of dads or pills with their own hands

To sew a cap in the form of dads you will need:

  • Fur;
  • Tissue for a subflade;
  • Paper for pattern or tracing;
  • Tape measure;
  • Needles, scissors, knife, marker and sewing machine.

Instruction:

  1. Measure the circle of your head. The height of the cap will be the height of the cap. For a pattern in the form of a circle, you can also apply the length of the rectangular billet;
  2. Create a pattern. Transfer the received parameters on the traction or paper. On the lines cut the sample. As a result, a circle and rectangle should be released;
  3. At the inside of a fur piece, attach and circle a rectangular figure and a circle with a marker. With the help of a knife or scalpel, cut the details data.

Important ! In order not to damage the fur, it is necessary to cut, it is not a pile, but directly fason furs. Be careful.

  1. Cut the same details from the fabric as from fur;
  2. Turn the fabric and fur on the wrong one. Connect the sides of both billets and secure them with pins. Then on the sewing machine, make lines - centimeter from the edge;
  3. Carefully inspect the fur and the direction of the pile. This is necessary to determine the place where the connection will occur with the circle;

On a note : Vile on such caps are usually directed towards the face.

  1. Remove both blanks again - the circle and the rectangle on the wrong side and connect the pins together;
  2. Pull up 1 cm from the edge of the circle, so that both parts are interconnected;
  3. Remove the cap on the front side and release the pile in the shine;
  4. In the same way, perept the billet from the tissue of the sublobe, but leave a small hole on it;
  5. Fabric Place in the fur blank to connect the edges. Secure all the pins and make the machine again;
  6. Remove the resulting cap using the gap, which is left in clause 10.;
  7. Manual seams close the hole;
  8. Align all and correct, then draw and shake the fur.

An unusual and very stylish headdress is ready. Such a style will be advantageous to look together with a warm coat from Drapa, wool, etc. As you can see, she is not so difficult to sew a hat from fur. The main thing is tool.

Fur hat Two-color

For its manufacture, prepare the following materials and tools:

  • Fur natural 2 contrasting colors and not very thick;
  • The old hat knitted or sweater (if at home did not find, you can buy or tie themselves);
  • Acute blade, scalpel or stationery knife;
  • Threads, needle;
  • A small piece of skin;
  • Sintepon and fleece (felt)

The principle of work is as follows:

  1. On the fur, make marking for bands for 7 mm;
  2. With the help of a stationery knife, blades, or scalpels cut the marked stripes. Be careful;
  3. As the basis, take the header or sweater. If the second, then take the bottom of the sweaters and attach the resulting strip to the forehead. The scalp must not be connected together;
  4. On the Sweater Strip, collect hinges in the needles and close them. If you do not know how to knit, then collect them on the gum, or thread;
  5. To the convex part of the workpiece, start to sew fur strips, alternating light - dark colors;
  6. Bands of dark fur It is advisable to make shorter light, but everything comes from your imagination and existing material;
  7. Couple into the ring brow with fur. Apply a hook or thread with a needle;
  8. Skin, with a diameter of about 12 cm, close the top hole (you need not need to sew up from above, but slightly adding). In the middle, we also lay down a bit of synthipon, and close the hole with a fleece, or a felt;
  9. Remove the hat. To straighten the fur, make it well, straighten and shake it a bit. All is ready!

A little effort and you will get an interesting and fluffy two-color hat.

Video: Master class: how to sew a hat from the old pest collar

Fur hat

For this cap, such tools and materials are needed as:

  • Pieces of fur;
  • Braid;
  • Paper or paper tank;
  • Santimeter tape, scissors, portno chalk;
  • Tissue for a subflade;
  • Wooden hammer and small nails;
  • Board of plywood.

Sewing instructions:

  1. Create a pattern: Cap from 2 parts, ears and a visor. To do this, mark on paper or tank a horizontal line of 30.5 cm long, in its middle, make a line of 14 cm high, which should be perpendicular. From the intersection point, back up - 2 cm vertically. Next, make another horizontal line 28, 5 cm. It should cross the in the middle of the length vertical strip;
  2. Make four more horizontal strips - 27 cm, 25.8 cm, 22.5 cm and 17 cm and retreat twice 3 and 1.5 cm. From the final drawn point, take up 3 cm and mark this place. Connect all left and right points with the top;
  3. Mark the outlet. To do this: Route up 4.5 cm along the central vertical and to the right, left at the bottom horizontal from the central point - 3 cm;
  4. Make a hand of a cauldrop. Make a horizontal line in a length of 13.5 cm. Divide it into 2 parts, from the center Create a perpendicular vertical line at 12 cm. Mix the bottom of the point at 3, 3 and again 3 cm, after 1.5 and 1, 5 cm. From these points, spend the horizontal bands 12.6; 11, 9, 7 cm. The middle of each strip should fall to marked points. All points are connected to each other;
  5. To form half the pattern of the visor, you need to build a drawing. Make a rectangular figure with dimensions on the paper - 11.5 and 13.5 cm. On the side of 11.5 cm set aside 3, 2 and 5 cm. On the opposite direction from these points you need to make perpendicular lines. There are 0.5 points on them; 2, 3, 5, 11 cm. Connect them. The resulting line will denote the front strip of the visor;
  6. On another smaller side of the rectangle, postpone the segment at 9, 1 cm long, then 3 times with 0.8 cm. From these points, draw perpendicular lines to the opposite side. On the 2nd perpendicular, tick 7, on the 3rd - 10 cm. 9.1 cm point, combine with a point on the opposite corner, with points - 0.8 / 7 cm, as well as 0.8 / 10 cm. This line will become rear strip visor;
  7. All samples place on the board and circle chalk. Attach fur;
  8. Stitches Sustrate pieces of fur. Vors should not fall on the wrong side. Spread the detail made, break the seam with a wooden hammer. Moisten the fur and straighten the pieces. Secure them with small carnations on the plywood. Vors should be out. Let fur dry;
  9. Remove the fur from the board, lay out the details of the pattern, outline their tailor chalk. Make patterns of 2 parts of the cap, 4 parts of the ears of the cap and the visor. Build the folding of the cap, then worst it. After, the sew ears and a visor. Remove the fur to the outside and enter the tape for testes;
  10. By oblique decompose the cloth for a subdish, move the details of all the patterns on it, cut down along the contour, sew together, smooth and enter into the resulting cap from fur. Please make repost

    Fur Cap Usanka Patterns

Despite the fact that it is not so easy to sew such a cap, as a result, it turns out a chic and fashionable headdress, which will necessarily warm even in a harsh winter.

Do not be afraid to sew, because it makes you and your wardrobe unique and unique.

Video: Sew a hat from fur with their own hands

[Total: 5Middle: 3.6. /five]

We sew a fur hat ourselves: a detailed master class on 3 models.

Want to try working with fur and sew a small product? There are pieces of fur and you think what to do with it? We offer to sew a fur hat and in the process of mastering the basic subtleties to work with the fur.

Fur hat with their own hands: choose the material for the product

Want to sew a hat from fur with your own hands? To begin with, let's choose the fur so that the finished product is worn and pleased the hostess.

  1. Matte or with glitter. If you are a matte fur skin, then that you do not do, the brilliance does not add. There are types of fur that originally matte, it is a matte muton, lama, sheepskin, etc., but most of the fur we perceive exclusively with glitter and gloss. Therefore, no matter how thick fur, but if it is dim and matte (not counting above), it is better not to use it for the cap;
  2. Fur condition Watch the skin, spend on it with a wet hand, slightly extend the comb with rounded teeth. If the fur rolls - it will quickly lose its appearance and shape. Better to work to take the fur, the hairs and sweat of which are dense and well held on the spot;
  3. Mebel. This base, the wrong side and the same skin on which the hairs and the edge are held. It should be elastic, elastic and not crack when flexing. It is not necessary to take into the work of a fur with a torn meter.

In order to sew a hat from fur, it may be necessary for both one and several types and shades of fur. It all depends on your preferences. It also takes a sewing machine or gypsy needle for manual seam, a lining for caps and other materials.

To work with the skin and fur, it is necessary to master the speed seam, it is not difficult, and you can learn immediately on the product. The nuances can be mastered by looking below the short video.

VIDEO: SUKER SOV DIY without a speed car

Fur hat with your own hands: Tablet model

Interested in the question how to sew a hat from fur with your own hands, but do not know which model to choose? The best one proven method is fitting. Go to the store and try on the caps, only 20-30 minutes and you decide which models suits you.

But there is a win-win version - a fur hat tablet. This model is suitable for absolutely everyone, the main thing is to determine the color, height and pomp hat. Well, we will tell how to sew such a hat from fur with their own hands.

To work, we will need:

  • Paper sheet for pattern, pencil and ruler;
  • Santimeter tape, if you do not know the exact volume of your head;
  • Fur;
  • Lining fabric;
  • Stationery knife or blade;
  • A pen;
  • Needle and durable thread number 40;
  • Sewing machine.

So, begin with the construction of the pattern. For example, we present photos of the pattern, but only as a sample for work.

Pattern caps Tablets from fur with her hands
Pattern caps Tablets from fur with her hands
  • Blacks are infected with a 58 cm rectangle (the volume of the head can be from 48 (children's) to 60) in length and from 10 cm to 14 high, depends on the size of the header, in our case 12 cm;
  • On the left and right at the bottom of the rectangle, as shown in the photo, we postpone the vertical lines of 2 cm (for all sizes standard), and carry out a smooth line to the bottom. It turns out a straight line with rounded ends;
  • In the middle we are making a dotted vertical line dotted line. On top of this line lay 1.5 cm (for all sizes standard);
  • Top posting 2 cm (for all sizes standard) on the right and left, but already on horizontal lines and from the middle, where the point -1.5 cm is put on the edges to the edges;
  • You must have a figure as on a photo sample.
  • We draw a circle with a perimeter equal to the perimeter of the vertex patterns. In our case, it is diameter 16. Standard formula for finding this value p = π d;
  • Cut out the paper out paper, apply to the meter and outline the handle. We do not forget to add 0.5 cm per battery;
  • For cutting, you will need a blade from the T-shaped razor or a sharp stationery knife, you can also use the scalpel.
  • We make a small incision (a couple of millimeters) and, raising the fur, carefully cutting a member. Ideally - cut only in Mezrah, not touching even the pod. In this case, the loss of valuable fur will be minimal, and you will not have a chopped pile and countertops;
  • Now we do cut on the lining;
  • We fold the long part of the lining in half, we descend, we flash on the machine, we apply a circular donyshko, we descend and spend on a typewriter, process the edges;
  • We fold on the same principle, but already fur, watches that the fur does not get out of the wrong side, if you need to correct and flash the speed suture;
  • We apply the bottom and also flash;
  • Soak the cap and check the quality of the seam, if somewhere there are shortcomings - plowing the seam and we flash again. We check until everything is satisfied. But if you do not stretch and do not tighten the skin - most likely you will die well the first time;
  • Now turn out again to the wrong and put the lining. From the wrong side, in several places, we grab the lining in several places so that it is perfect in the header, and then we flash the secret seam along the edge, so that the edges of the lining and the meters are hidden under the seam;
  • It remains only to combine, try and go for a walk.
Mink Tablet Cap
Mink Tablet Cap

Cap of fur with her own hands: Kubanka

Want to sew a hat from fur with your own hands in the form of Kubanka? We will not dwell on the raw materials for this cap, as it completely coincides with the previous one, and we will immediately go to the pattern.

Pattern caps Cabanka from fur with their own hands
Pattern caps Cabanka from fur with their own hands

Please note that the pattern is built on a head with a head with a scalp 50 cm. If the size of the head is different, the parameters change exactly proportionally. We leave 1 cm on the seams so that they additionally keep rigidity.

Now we turn to the cut and assembly:

  • We lay out the pattern so that the fur on the Tulley lay down to the bottom of the Tula (look at the photo of the finished Kubanka, and the direction will become clear), also pay attention to the top edging, it is best to choose the fur for this part. As in the previous master class, we cut the blade, scalpel or a stationery knife slightly raising the fur;
  • We also make a pattern with lining;
  • Making the lining assembly to make it clearer how to collect more expensive fur. To do this, we sew a lush edging with the help of a speed seam, and an edging is sewn a round bottom;
  • We grab to the bottom in several places lining and turn the product;
  • Check the quality of the seams and turn inside out again to sew the lining.

Please note that the Kubank model is very unpredictable. Depending on the textures, the figures of fur and other factors are obtained by unrecognizable different models.

Makeup hat do it yourself patterns
Cabank Cap from fox fur with their own hands. Decorated with fox tails

Cap from fur with their own hands: Ushanka

When we talk about the fur caps first that comes to mind - Ushanka. They are different, both with a fur visor and ears, and completely fur.

To work, we need a pattern.

Pattern of the header of the Ushanki with the detailed markup on the volume of the head 56 cm
Pattern of the header of the Ushanki with the detailed markup on the volume of the head 56 cm
Cabank Cap from fox fur with their own hands. decorated with fox tails
Detailed pattern Visor of outdoor and inside for machines from fur
  • I cut the parts with the allowance of + 1 cm.
  • We also make marking on Mezer and with a reserve of + 1 cm make a pattern. Do not forget about the direction of fur. If you want to fall on the weapons - duplicate the ears on 4 parts, and they are not needed in the lining;
  • If you want from fur to make only the edge, and the basis from another material, then this is exactly what we cut. By the way, if a few years in a row were in fashion, leather menu-emitted headers with a fur edge, today there are completely fur hats in fashion again;
  • We start assembling the lining, it will be easier to navigate with fur. We grasp the typewriter and process the edges;
  • Start assembling the caps of the erase of their fur is best with the bottom. Two semicircons are sewed to it, there are ears with the back and the visor last. In order to add a visor an extra volume - insert into the inside a piece of syntheps. It will add volume and reveals the beauty of fur;
  • And in conclusion, it will remain sunmove to the header and hide the ends. You can also install accessories so that the visor and ears can be fastened-tolerate at will.

It is important to remember that if the skin is harsh and keeps the shape, you can sew right away. But if a soft fur with a fine member came to work - it must be treated with Dublerin, to give stiffness.

Hand hat from fur with her hands
Hand hat from fur with her hands

In order to make a hat from fur with your own hands in the model of the Ushanka, the skills of sewing and understanding of the assembly are required. If you are new, we recommend watching a video master class.

Video: Sewing Fur Hap

How to sew a fur hat with your own hands: step-by-step guide tailoring caps of artificial and natural fur

How to sew a fur hat with your own hands

In winter, special attention should be paid to choosing a headdress. Human health depends on it. Hoods made of natural fur are the most warm and beautiful. They are much more expensive compared to the rest of the heads. However, there are many ways to sew it with your own hands.

Women's Fur Haps Reviews

Fashion trends do not stand still. Every year new models of female hats appear. There are options that do not lose their relevance. To them, primarily include the volumetric menu hats and caps-berets. They, in turn, have many modifications depending on the design and the type of fur. Evoid popularity and caps of artificial fur. They are distinguished by a variety of color solutions and affordable price.

What fur is better to sew a hat

The selection of fur is determined by the personal preferences of a person and its financial capabilities. Also cost to take into account the upper clothes with which the headdress will be worn. The cap should be combined with the selected manner or emphasize it. So, the product from the skirts of the fox will be very spectacular and bright. Therefore, it is necessary to understand in advance with what it looks harmonious.

On a note! The most in demand when sewing female headquarters mink, sands and leopard. Budget products are considered to be products from rabbit, and more elite - from furs and other valuable animals.

Natural fur hat with their own hands

One of the popular models in women is a cap in the form of a dad or pill. It combines perfectly with a drape and woolen coat and is suitable for absolutely all women. The main thing is to choose its height. Her feature is to visually increase the head. To sew such a thing need a fur, a cloth for a lining, paper, a knife, thread, needles and a sewing machine.

Caps pattern

The pattern of the model consists of two elements: a circle and a rectangle. To correct it correctly, it is necessary to measure the circle of the head with a centimeter tape. The height of the product is taken on the basis of personal preferences. There should be a rectangle with the sides of equal height of the product and the width of the head. For the circle pattern, the length of the obtained rectangle is used. Patterns draw on paper and cut out.

We sew a hat from natural fur step by step

Sew a headdress on your own in a couple of hours. To do this, follow the following sequence of actions:

  1. Position the patterns from the wrong side of the fur skin and attach them with pins. Next, they are driven by a marker and make an increase on the seams about 1.5 cm.
  2. Details are neatly cut with a knife or scalpel.
  3. The same details must be made of lining fabric.
  4. Compound of fur and lining with irons. They are fixed by pins and stripped by car 1 cm from the edge.
  5. Before connecting the header with a circle, you should carefully examine the direction of the villi. In such options, they usually look at the person's face.
  6. The circle and rectangle are connected to each other by involvement with a pin.
  7. Next, they are stepping with each other on a type of 1 cm from the edge.
  8. The cap is turned on the face and free the seam from the pile stuck there.
  9. Next, the fabric lining is placed in the fur blank and are cleaned with pins. A small gap must be left so that the header can be turned out.
  10. The fur billet and the lining are firmware and turned out.
  11. The unpripted hole is handled by a manually secret seam.

REFERENCE! At the end of the sewing, the resulting cap shakes and slightly calculate the fur.

How to sew a hat from artificial fur with their own hands

Hatts made of artificial fur are no less beautiful than from natural. And if you make a compacted lining, then the ability to keep the heat they will not give up. In addition, on artificial fur, it is possible to practice if I sew such a product for the first time. The model with long ears from the back looks very effectively and extraordinary. Of particular popularity in young girls. For its manufacture, you need a cut of the fur 20 cm in width and 160 cm in length.

Pattern for the header

To build patterns, you need to draw a rectangle with a length of the head of the head and width of 20 cm. Blacksmithing two tails in length are 35 cm, and in width 10 cm. Their tip can be made pointed. Cut the patterns drawn on paper and cut them out.

We sew a hat from artificial fur step by step

Prepare all the necessary materials, begin the process of sewing the product in the following sequence:

  1. He imposes patterns from the wrong side of the fur skurt and fasten them with pins. We supply the marker or chalk, leaving the allowance for the seams about 1 cm.
  2. The details obtained neatly cut out.
  3. We take the base of the cap and fold the front side inside and stitch, manually without reaching the end of 15 cm so that it is more convenient to sew tails.
  4. Next, we take the tails and sew to the header, not reaching each edge 1 cm.
  5. Next, we do to the end of the remaining 15 cm of the base of the header.
  6. Turn the cap on the front side.
  7. We start sewing tails.
  8. With the help of a centimeter tape, you measure the girth of the head, fold the cap in half and stitch.
  9. We find the middle of a headdress and sew, making small park assemblies up.
  10. For beauty to the product you can sew a spectacular brooch or a servor.

IMPORTANT! For this model, it is better to select a volumetric fur with a long pile.

Features of sewing products from natural and artificial fur

There are certain nuances that need to be considered when working with fur. Thus, when cutting parts should be flexing the fur in the opposite side to cut the skin and affect the valuable pile. The tool must be well sustained to not tear the skirt.

ATTENTION! In specialized firms for tailoring of fur products, focusing machines are used. On the usual sewing machine, it is difficult to sew the product, and sometimes it is impossible. It is necessary to carefully select thick needles and sew slowly with a large stitch, so as not to spoil the car. In some cases, it is better to use a simple thread and needle.

You can even attend yourself with a fur product that does not even have large financial resources. Observing simple recommendations for the season it is possible to sew a few spectacular hats of both natural and artificial fur.

How to sew a fur hat with their own hands

In winter it is very important to wear a headdress. In particular, the inhabitants of cold regions are needed warm and dispropal protection for the head. The ideal option will be fur hat . And it is not necessary to run for her to the store. The homemade hat, the so-called hand-made, will make your headdress not only functional, but also unique. We give for you, needlewomen, three examples of how to sew a hat from fur with their own hands.

Stylish fur hat in the form of dads or pills with their own hands

To sew a cap in the form of dads you will need:

  • Fur;
  • Tissue for a subflade;
  • Paper for pattern or tracing;
  • Tape measure;
  • Needles, scissors, knife, marker and sewing machine.

Instruction:

  1. Measure the circle of your head. The height of the cap will be the height of the cap. For a pattern in the form of a circle, you can also apply the length of the rectangular billet;
  2. Create a pattern. Transfer the received parameters on the traction or paper. On the lines cut the sample. As a result, a circle and rectangle should be released;
  3. At the inside of a fur piece, attach and circle a rectangular figure and a circle with a marker. With the help of a knife or scalpel, cut the details data.
  1. Cut the same details from the fabric as from fur;
  2. Turn the fabric and fur on the wrong one. Connect the sides of both billets and secure them with pins. Then on the sewing machine, make lines - centimeter from the edge;
  3. Carefully inspect the fur and the direction of the pile. This is necessary to determine the place where the connection will occur with the circle;
  1. Remove both blanks again - the circle and the rectangle on the wrong side and connect the pins together;
  2. Pull up 1 cm from the edge of the circle, so that both parts are interconnected;
  3. Remove the cap on the front side and release the pile in the shine;
  4. In the same way, perept the billet from the tissue of the sublobe, but leave a small hole on it;
  5. Fabric Place in the fur blank to connect the edges. Secure all the pins and make the machine again;
  6. Remove the resulting cap using the gap, which is left in clause 10.;
  7. Manual seams close the hole;
  8. Align all and correct, then draw and shake the fur.

An unusual and very stylish headdress is ready. Such a style will be advantageous to look together with a warm coat from Drapa, wool, etc. As you can see, she is not so difficult to sew a hat from fur. The main thing is tool.

Fur hat Two-color

For its manufacture, prepare the following materials and tools:

  • Fur natural 2 contrasting colors and not very thick;
  • The old hat knitted or sweater (if at home did not find, you can buy or tie themselves);
  • Acute blade, scalpel or stationery knife;
  • Threads, needle;
  • A small piece of skin;
  • Sintepon and fleece (felt)

The principle of work is as follows:

  1. On the fur, make marking for bands for 7 mm;
  2. With the help of a stationery knife, blades, or scalpels cut the marked stripes. Be careful;
  3. As the basis, take the header or sweater. If the second, then take the bottom of the sweaters and attach the resulting strip to the forehead. The scalp must not be connected together;
  4. On the Sweater Strip, collect hinges in the needles and close them. If you do not know how to knit, then collect them on the gum, or thread;
  5. To the convex part of the workpiece, start to sew fur strips, alternating light - dark colors;
  6. Bands of dark fur It is advisable to make shorter light, but everything comes from your imagination and existing material;
  7. Couple into the ring brow with fur. Apply a hook or thread with a needle;
  8. Skin, with a diameter of about 12 cm, close the top hole (you need not need to sew up from above, but slightly adding). In the middle, we also lay down a bit of synthipon, and close the hole with a fleece, or a felt;
  9. Remove the hat. To straighten the fur, make it well, straighten and shake it a bit. All is ready!

A little effort and you will get an interesting and fluffy two-color hat.

Video: Master class: how to sew a hat from the old pest collar

Fur hat

For this cap, such tools and materials are needed as:

  • Pieces of fur;
  • Braid;
  • Paper or paper tank;
  • Santimeter tape, scissors, portno chalk;
  • Tissue for a subflade;
  • Wooden hammer and small nails;
  • Board of plywood.

Sewing instructions:

  1. Create a pattern: Cap from 2 parts, ears and a visor. To do this, mark on paper or tank a horizontal line of 30.5 cm long, in its middle, make a line of 14 cm high, which should be perpendicular. From the intersection point, back up - 2 cm vertically. Next, make another horizontal line 28, 5 cm. It should cross the in the middle of the length vertical strip;
  2. Make four more horizontal strips - 27 cm, 25.8 cm, 22.5 cm and 17 cm and retreat twice 3 and 1.5 cm. From the final drawn point, take up 3 cm and mark this place. Connect all left and right points with the top;
  3. Mark the outlet. To do this: Route up 4.5 cm along the central vertical and to the right, left at the bottom horizontal from the central point - 3 cm;
  4. Make a hand of a cauldrop. Make a horizontal line in a length of 13.5 cm. Divide it into 2 parts, from the center Create a perpendicular vertical line at 12 cm. Mix the bottom of the point at 3, 3 and again 3 cm, after 1.5 and 1, 5 cm. From these points, spend the horizontal bands 12.6; 11, 9, 7 cm. The middle of each strip should fall to marked points. All points are connected to each other;
  5. To form half the pattern of the visor, you need to build a drawing. Make a rectangular figure with dimensions on the paper - 11.5 and 13.5 cm. On the side of 11.5 cm set aside 3, 2 and 5 cm. On the opposite direction from these points you need to make perpendicular lines. There are 0.5 points on them; 2, 3, 5, 11 cm. Connect them. The resulting line will denote the front strip of the visor;
  6. On another smaller side of the rectangle, postpone the segment at 9, 1 cm long, then 3 times with 0.8 cm. From these points, draw perpendicular lines to the opposite side. On the 2nd perpendicular, tick 7, on the 3rd - 10 cm. 9.1 cm point, combine with a point on the opposite corner, with points - 0.8 / 7 cm, as well as 0.8 / 10 cm. This line will become rear strip visor;
  7. All samples place on the board and circle chalk. Attach fur;
  8. Stitches Sustrate pieces of fur. Vors should not fall on the wrong side. Spread the detail made, break the seam with a wooden hammer. Moisten the fur and straighten the pieces. Secure them with small carnations on the plywood. Vors should be out. Let fur dry;
  9. Remove the fur from the board, lay out the details of the pattern, outline their tailor chalk. Make patterns of 2 parts of the cap, 4 parts of the ears of the cap and the visor. Build the folding of the cap, then worst it. After, the sew ears and a visor. Remove the fur to the outside and enter the tape for testes;
  10. By oblique decompose the cloth for a subdish, move the details of all the patterns on it, cut down along the contour, sew together, smooth and enter into the resulting cap from fur.

Fur Cap Usanka Patterns

Despite the fact that it is not so easy to sew such a cap, as a result, it turns out a chic and fashionable headdress, which will necessarily warm even in a harsh winter.

Do not be afraid to sew, because it makes you and your wardrobe unique and unique.

Patterns Caps-Ushanok Fur

The cap is the necessary attribute for the cold season. Happers-Ushanki - the optimal solution so that the image is stylish and fashionable, and the head and ears were warm and comfortable. Supplemented by ridiculous ears, contrasting fabrics and colors, such headwear will greatly dilute the gray winter dullness. In addition, this model copes perfectly with its direct task - the protection of the head from frost and wind. The caps can be knitted or stitched, made of fur or from batting, on a synthetic tube, on a flue, on a lining or even atlas and silk. Modern industry provides a huge selection of accessories.

History Hat-Ushanki

Initially, the caps were a male accessory. They were worn by hunters, researchers, prospectors. Warm caps perfectly defended cheeks, ears and heads from cold and penetrating wind.

A few years ago, Malahai was considered popular only from the older generation. But modern designers changed the appearance of the head of the head, giving him the popularity of young people. In addition, such headquarters have become popular and in the female population. Patterns of female hats, female and male, like the sewing technology itself, are completely identical. The difference can only be in the finish, the length of the "ears", the style of the strings or the form of fur.

It is not necessary to acquire such a hat in the finished form. You can independently sew a hatching cap, the pattern is easy and simple.

How to choose Material

This headdress may be knitted, knitted, fleece. However, fur caps are most popular and practicality.

Fur can be both natural and artificial. Natural - Sobat, Corn, Otter, Ontatra, Chinchilla, Rabbit. Each of the species has both advantages and disadvantages. The most important nuance - for sewing such fur, it is necessary to use a large number of equipment: hammers for breaking seams, a special speed knife, scissors and needles of a special form. In addition, it is necessary to sew it either on the feeding machine or manually. And the one and other technology requires some skill and practice.

Artificial fur can be sewed on an ordinary sewing machine. Unlike natural, it is most often cheaper several times. Its durability is less, and it is more susceptible to wear, however, the replacement of such a product will be much easier.

The lining for the caps is required. If the patterns of the headers of the earlots can be used any, then the lining can be any. Fleece or special lining fabric is most often used. In combination with the fur, they create an additional thermal barrier. In addition, the lining protects the fur from wear - the contact of the hair cover of the head and the skin of the forehead takes place with the lining cloth, which, if necessary, it is much easier to wash or replace the new one.

How to shoot Merki

To build patterns it is necessary to remove the hearts of the head. The following indicators are removed:

  1. Scalp (OG). To remove the measurement centimeter should pass around the head circumference through the forehead and on the base of the skull. The tape should not put very much on his head.

For standard size 56-58, measurements will be:

  • Og - 55 cm;
  • Vg (1) - 40 cm;
  • Vg (2) - 61 cm;
  • RV - 18 cm;
  • Ru - 30 cm.

How to build a pattern

The patterns of caps-earplugs are built according to the scheme, which results in a conditional grid. On this grid, the contour, which shapes the heads of the caps.

On paper A3 format in the upper left corner, point A1 is noted.

  1. A1A2 segment is postponed to the right of it - a semiculture of the head. For a hat with a lining or insulation, 1 cm is added. Eases 29.5 cm.
  2. Down from point A1 is marked by A1N1. The distance is half the height of the head 2. The insulation is added 1 cm. Total - 31.5 cm.
  3. Right from H1N3 marks another segment - A1A2. A2H3, which is equal to A1N1 is built from A2. At the end of the construction, it turns out a rectangle A1A2N3N1.
  4. Down from point A2 is lowered by a segment A2L1, which is equal (VG1-3) / 2. It turns out 18.5 cm. Point L1 is noted. Left from it is built perpendicular to A1N1.
  5. L1sh1 segment is postponed. It is built from point L1 down. Received segment sh1sh2.
  6. Left from H3 is built H2N3. This distance is half the distance between the ears. 0.5 cm is added to the lining. 15.5 cm is obtained.
  7. Up from H2 is built perpendicular L1.
  8. Left from L1 is postponed L1l2. This distance is ½ measurements between the temples. 0.5 cm is added to the lining. It turns out 9.5 cm. The perpendicular is lowered to the P1N3 point.
  9. To the left of H2, the distance equal to the distance between L2Sh3 and H2 is postponed. A perpendicular line to H1N3 is built and sh4 is noted. Sh4Н2 = H2SH3.
  10. Bissectrix is ​​carried out from the corner L1L2Sh3. It is postponed on it segment L2L3. It is approximately 2.5-3 cm.
  11. The segment sh4sh6, which is 1-1.3 cm, is postponed on the bisector sh1sh4sh5.
  12. Cut A1N1 is divided in half and is noted by K1. It turns out 15.8 cm. Then the perpendicular line to A2H3 is carried out from this point. At the intersection of K2 is placed.
  13. Calculated point K3. K1K3 is half K1K2. It turns out 14.8 cm. Up is the perpendicular line, up to the intersection with A1A2. A3 is noted.
  14. It is calculated A1A4. The distance is A1A5 or A1A3, divided by 2. extends 7.4 cm.
  15. K1 and A4, A4 and K3, K3 and A5, A5 and K2 are connected.
  16. Perpendiculars are built from the serin of the resulting segments. All perpendicular lines are segments of 1-1.3 cm.
  17. At the end of the constructions through all the points obtained (W1, K1, K4, A4, K5, K3, K6, A5, K7, K2, L1, L3, C7, N2, S5, L3), a smooth envelope line is carried out.

Pattern of the hatching caps from fur is ready.

By changing the smoothness of lines and fades, the cap can be slightly modified: make ears longer than, add or remove the dye top.

The simplest pattern is the cap-tablet. To build it requires OG and BG2. The circle is drawn, the diameter of which is 1/2 og. Also draws a rectangle height of VG2 and a length equal to the scuffing of the head + 1 cm on the seam + 1 cm on the lining.

The ears are cut in the form of two triangles, the base of which is equal to the distance from the temple to the edge of the ear, and the length is selected so that the ears are closed the cheeks.

How to paint fur

When it is ready to correctly pattern the caps of the Ushanki, the details of the future headdress are cut out of the fur.

The fur lies with a special frown knife. It is possible to do this with the help of tailoring scissors, but in this case the pile will be cut and hide the seams that will result in the result.

The cuts are conducted with a member knife (this is the basis, in fact, the skin from which the pile is growing) or the bachtarma (dublinka substrate). The knife is kept in the right hand. Movements are produced on weight. With the right hand, the cut part is fixed, and the left is removed extra parts.

How to sew details

Always need a high-quality hat-Ushanka. With their own hands, the pattern has already been made and the details are cut out, now part of the skins are stitching.

Fur before stitching must be prepared. The edges must be very smooth and neat. Mebel stretches, so you can mark the control points. They must come together when stitching.

Details are stitched with fur inside. On the right hand on the middle finger is necessarily put on the thimble. Cut parts are located on the middle finger of the left hand, pressed large. Control points must be combined. From the seat of the seam is definitely removed wool. It must be fed by a needle, a finger or a special tool similar to a circulation, inside.

Skrew sov

Patterns of hats-earlots often contain decorative elements. The most durable seam for their compound is a speed.

The seam is performed on the right left. The step should be small. Thread must be well tightened. The next stitch is made without offset, in the same place. Then the needle moves to the left, stitch forward, in place. The needle passes twice in the same hole. It is important to remember that puncture of the skin is "on yourself".

Depending on the density and elasticity of the Member of 1 cm may be 3-4 stitches. From the edge of the fur, it is necessary to retreat from 1.5 to 3 mm.

Stitching is made in the direction of fur. Vile, which fell on the wrong side, pull the needle on the face.

When the part is stitched, the seam unfolds online. A fur with a short pile is warm up with a finger, and not smoothed.

Lining sewage

By the pattern, which was built for the header, draws the pattern for lining. The lining fabric usually does not stretch, so it is necessary to take into account its properties. Most often an increase is 0.7-1 cm.

The lining is sewn from the wrong side. For the best adjacent lining to the fur, the sewing is made simultaneously with how the skin parts are sewn. At the same time, a small lip of the lining tissue is inside, which does not allow to fasten the threads of the sublock.

You can sew a lining separately and paste it into the finished cap, to fasten it or walk the seam along the edge of the product. This method is not very convenient, since on the back of the cloth, the fabric will not hold on and can be knocked back, and then fastened.

Decoration

The hat can be decorated with a shame - visor over his forehead. It is cut out in the form of a rectangle and sewing strictly in the center.

Also, the caps should be strings. In warm weather, they are tested ears up.

The strings can be carved out of the fur and set the buttons to them. Also, this feature is perfectly performed with impregnation laces.

Easy to sew a hand hat with your own hands. The pattern is simply built enough, and it is possible to decorate such a headdress and modify your taste.

Pattern of fur caps: Improving tailor skills

Summer comes to an end, and the caps with Panama remain in the past. They replace warm hats from fur and knitwear. Not every woman has funds for an expensive mink cap, therefore there is an alternative way to acquire things with minimal cost. It is worth only to revise old clothes and find a fur coat that is unsuitable for socks. It is suitable for the pattern of the planned hat.

Where to start the cut?

First of all, you need to choose a fur for the pattern of the header. Skirts can be ordered on the site or buy on the market, but if there is no such possibility, the correct option is to search the old product from fur in the wardrobe. The most important subject with which the pattern will be created, this is a stationery knife or a sharp razor blade. It is worth considering that the size and shape of the head of each person is different, so you need to immediately measure the volume of your own head centimeter in order to further use measurements to build grids. Here is an exemplary list of objects that are needed to create a pattern of a hat caps:

  • fur (foxovy, mink, ermine, etc.);
  • graph paper;
  • stationery knife;
  • pins;
  • centimeter;
  • line;
  • Portnovo chalk.

When building a pattern, it is necessary to take into account the allowances on the seams, and on the fur - the direction of the pile. It is important to know that the fur puts the pile down so that its structure does not be damaged with a string, the incision is made neatly on the skin. If the material got into the wardrobe, it is worth sprinkling it with water, combing and let it dry. The same method acts when stretching the skins, only water is applied to the skin.

Types of patterns of fur hats

There are many patterns of female hats from fur, which are easy to make with their own hands. The only question is which material to choose. The basis of the cap can serve as a leather or knitwear, and as a lining often use Sargo. The stylistics range is unusually diverse: from classics to animal figures (cat ears, wolf). The most replaceable are considered:

1. The caps of the machines made of fur, the patterns of which have 12 parts: 2 ears, 2 wedges, 4 medium wedges and 2 parts of the visor. Wedge is a kind of "petal", tailored from fur, and the visor is a detail that sews in front of the product.

2. Caps, "semi-seams", tied under the chin, often carry children. Patterns of children's hats from fur are made on the same principle as for adults, only they differ in size.

3. Cap-Boyarka is the most simple in execution, because it has only 4 parts that need to be sehered.

Pattern starts with paper

You need to use a centimeter to measure the head circumference, the distance from the ears, forehead and the nape to the middle. All removed measurements are applied on paper for grids. Boyarka Cap from Fur is easy to perform, because it consists of only four parts:

• top of the product; • visor; • Punches; • Lining walls.

The top of the caps also consists of four separate details that are similar to pointed petals. If you take a cap or any leather cap and consider it carefully, you can see the seams on the sides. These are stitched wedges. The magnitude of the circle of the head must be divided into 4, and the resulting number to take the width of the petal and draw the line on the paper. The final wedge mark must be put perpendicular to the width lines, considering the distance, for example, from the ear to the middle of the head. The ends of the wedge with this mark are connected. Then you need to retreat from the part 1.5-2 cm and lay the dotted point of the seams. First wedge is ready. These will need to do three more. The width of the visor is chosen arbitrarily, and the length is taking into account the size of the head and allowance. Rodyshko and walls are built on the same principle as the visor. When the paper pattern is ready, it must be transferred to the fur with the help of Portnovsky chalk and cut out the stationery knife.

How to create a pattern of machines from fur?

Man's head length - 55-58 cm. These parameters must be taken into account when building a lecturer for the pattern of a hat caps. For convenience, during the construction, paper folds in half. 23 cm is postponed from the middle of the top, and the width takes 12 cm, it will be a side part.

Ears consist of two parts - rectangle and square. The first part in a width of 11 cm, and the length in the width of the album sheet, the second side is 9.5 cm. The finished patterns are cut, they jumped to the wrong side of the fur and are melted with chalk.

Pattern of the children's caps - is it difficult to do?

First you need to select the appropriate model. Details of the children's head reminder can resemble parts of the female hats from fur, but may differ in structure, for example, ears, decorations, ties with pompoms. If you tune in to work and make patterns, focusing on instructions, then there is nothing difficult in the work. To facilitate the process, an artificial fur can be used, which does not require preliminary training (stretching, styling). Such a material is easy to care, it is easier to clean it, it is easier to work with it during sewing.

How to improve the quality of the cuts?

Be sure to remember that the cutting caps from fur should be taken into account of the seams of 1.5-2 cm. After completion of the work, the finished product should be sprinkled with water, comb and dry. It is worth seeing whether there is no irregularities, whether the fur is processed and whether the materials are not damaged with strip or sewing. The quality of work corresponds to the level of the master's experience. By creating your own model, you can not neglect the basics and specified clause standards, otherwise the patterns are obtained by substandard, work will have to redo. All possible shortcomings are easier to fix in the process. If the cap is less than less, it is worth adding a couple of wedges or recalculate measurements and alter.

Making a fur hat

  • April 30, 2015.
  • Reviews: 0.
  • Views: 26482.

Making a fur hat "Pussy" from the ondatra

Today you will learn how to independently sew a fur hat "Pussy" from natural fur ondatra. In the conditions of the crisis, not every girl can afford a mink, but it always wants to look stylish. Ondatra comes to the rescue, its fur is quite dense and even, and on wear resistance, the quality of fur does not lag behind a more expensive mink.

But the Ontatra proposed by the average man is usually wild, we use the Canadian cellular, the difference is obvious. We will sew a hat from the Canadian ondatra, so that you have learned the whole process from A to Z.

So, we have a skin, isolated and painted black in the Russian factory. I strongly do not recommend that the handicraft and Chinese dressing is sewed, the product will last for a short time.

How to cut the skin

First of all, we look at the skin, there should be no defects on it, if they still found a lush, gently cut the skin of the skin and sew the place of the cut.

Soak and cut the skirt as shown in the figure.

The cut line is strictly in the center of the abdomen. It is not necessary to use the knife of the cutter, the more you probably don't have it, but you can buy in any Gillette supermarket, which will perfectly cope with your task. Then the skin with urinary warm water from the skin. We leave so for the watch, so that the elastic meter has become elastic.

The next step is stretching. To do this, we will use a sheet of plywood and furniture stapler. We need to stretch the skin to the size of the working surface, and this is from 24cm. width and 20 cm. Height. If the width is less, then it is better to postpone the skin on another model, since the cap will be seen through the strips, and this is damn not beautiful.

Our billet is broken up to the level of the working surface, we are waiting for its complete drying, i.e. Approximately 12 hours without a special drying. Dry skin, remove the brackets and begin to cast our workpiece. Pre-draw surface on 42 level lines, i.e. Each line we should have a width of about 60mm, it is not completely distressing from above, you need to get such an octopus as in the figure, because we will sew strips strictly in order, otherwise the differences will be noticeable and the cap will be noticeable.

The final stage

The most responsible moment occurs, we begin to sew strips with a knitted cap, the cap can be associated or buying ready, the amount of Ryube must match the amount of fur stripes, for the manufacture of Lemmex caps uses high-quality Turkish yarn, which does not stretch and serve you for a long time. The Chinese yarn is quite quickly losing the shape and stretch, ultimately not recommended for use. By the way, the height of our cap is 20cm.

If we want a soft landing and comfort, then you need to sew with a bend, well, if you do not have enough skills, you sew up to the edge, retreating about 50mm, every strip is fixed by a knot-clip, try to keep the pitch enough, do not exceed more than 0.5 cm Otherwise, the strips will begin to curvate and the hat will lose a holistic appearance.

So, arrange more comfortable and start sewing your masterpiece. Important moment This is not strongly attributing the fur strip thread, there must be a slab, otherwise the headdress will crush.

Professional Shvent on collecting this model goes around two hours, you may need a whole day without skills. But as you know, the goal justifies the funds, and here our hat is presented with their own hands, please add bijouteria to the ears for greater expressiveness.

Did not happen bad, isn't it? We are waiting for your feedback and comment.

Detailed pattern Visor of outdoor and inside for machines from fur

In winter, special attention should be paid to choosing a headdress. Human health depends on it. Hoods made of natural fur are the most warm and beautiful. They are much more expensive compared to the rest of the heads. However, there are many ways to sew it with your own hands.

Women's Fur Haps Reviews

Fashion trends do not stand still. Every year new models of female hats appear. There are options that do not lose their relevance. To them, primarily include the volumetric menu hats and caps-berets. They, in turn, have many modifications depending on the design and the type of fur. Evoid popularity and caps of artificial fur. They are distinguished by a variety of color solutions and affordable price.

fur hat

     Fur hat Ushanka

What fur is better to sew a hat

Model Fur Hood

The selection of fur is determined by the personal preferences of a person and its financial capabilities. Also cost to take into account the upper clothes with which the headdress will be worn. The cap should be combined with the selected manner or emphasize it. So, the product from the skirts of the fox will be very spectacular and bright. Therefore, it is necessary to understand in advance with what it looks harmonious.

On a note! The most in demand when sewing female headquarters mink, sands and leopard. Budget products are considered to be products from rabbit, and more elite - from furs and other valuable animals.

Natural fur hat with their own hands

artificial fur

One of the popular models in women is a cap in the form of a dad or pill. It combines perfectly with a drape and woolen coat and is suitable for absolutely all women. The main thing is to choose its height. Her feature is to visually increase the head. To sew such a thing need a fur, a cloth for a lining, paper, a knife, thread, needles and a sewing machine.

Caps pattern

The pattern of the model consists of two elements: a circle and a rectangle. To correct it correctly, it is necessary to measure the circle of the head with a centimeter tape. The height of the product is taken on the basis of personal preferences. There should be a rectangle with the sides of equal height of the product and the width of the head. For the circle pattern, the length of the obtained rectangle is used. Patterns draw on paper and cut out.

Natural fur hat with their own hands

We sew a hat from natural fur step by step

Caps pattern

Sew a headdress on your own in a couple of hours. To do this, follow the following sequence of actions:

  1. Position the patterns from the wrong side of the fur skin and attach them with pins. Next, they are driven by a marker and make an increase on the seams about 1.5 cm.
  2. Details are neatly cut with a knife or scalpel.
  3. The same details must be made of lining fabric.
  4. Compound of fur and lining with irons. They are fixed by pins and stripped by car 1 cm from the edge.
  5. Before connecting the header with a circle, you should carefully examine the direction of the villi. In such options, they usually look at the person's face.
  6. The circle and rectangle are connected to each other by involvement with a pin.
  7. Next, they are stepping with each other on a type of 1 cm from the edge.
  8. The cap is turned on the face and free the seam from the pile stuck there.
  9. Next, the fabric lining is placed in the fur blank and are cleaned with pins. A small gap must be left so that the header can be turned out.
  10. The fur billet and the lining are firmware and turned out.
  11. The unpripted hole is handled by a manually secret seam.

REFERENCE! At the end of the sewing, the resulting cap shakes and slightly calculate the fur.

How to sew a hat from artificial fur with their own hands

sewing caps made of natural fur

Hatts made of artificial fur are no less beautiful than from natural. And if you make a compacted lining, then the ability to keep the heat they will not give up. In addition, on artificial fur, it is possible to practice if I sew such a product for the first time. The model with long ears from the back looks very effectively and extraordinary. Of particular popularity in young girls. For its manufacture, you need a cut of the fur 20 cm in width and 160 cm in length.

Pattern for the header

To build patterns, you need to draw a rectangle with a length of the head of the head and width of 20 cm. Blacksmithing two tails in length are 35 cm, and in width 10 cm. Their tip can be made pointed. Cut the patterns drawn on paper and cut them out.

We sew a hat from artificial fur step by step

Cap of artificial fur with their own hands

Prepare all the necessary materials, begin the process of sewing the product in the following sequence:

  1. He imposes patterns from the wrong side of the fur skurt and fasten them with pins. We supply the marker or chalk, leaving the allowance for the seams about 1 cm.
  2. The details obtained neatly cut out.
  3. We take the base of the cap and fold the front side inside and stitch, manually without reaching the end of 15 cm so that it is more convenient to sew tails.
  4. Next, we take the tails and sew to the header, not reaching each edge 1 cm.
  5. Next, we do to the end of the remaining 15 cm of the base of the header.
  6. Turn the cap on the front side.
  7. We start sewing tails.
  8. With the help of a centimeter tape, you measure the girth of the head, fold the cap in half and stitch.
  9. We find the middle of a headdress and sew, making small park assemblies up.
  10. For beauty to the product you can sew a spectacular brooch or a servor.

IMPORTANT! For this model, it is better to select a volumetric fur with a long pile.

Features of sewing products from natural and artificial fur

Cap of artificial fur step by step

There are certain nuances that need to be considered when working with fur. Thus, when cutting parts should be flexing the fur in the opposite side to cut the skin and affect the valuable pile. The tool must be well sustained to not tear the skirt.

ATTENTION! In specialized firms for tailoring of fur products, focusing machines are used. On the usual sewing machine, it is difficult to sew the product, and sometimes it is impossible. It is necessary to carefully select thick needles and sew slowly with a large stitch, so as not to spoil the car. In some cases, it is better to use a simple thread and needle.

You can even attend yourself with a fur product that does not even have large financial resources. Observing simple recommendations for the season it is possible to sew a few spectacular hats of both natural and artificial fur.

Like?

Loading...

Found a mistake? Highlight it and press Ctrl + Enter. We will fix everything!

Sewing fur hat

Sewing fur hat

This skirt was gave me a husband on the anniversary of the wedding.

Sewing fur hat

First you need to remove the paws and sew all holes. Stretch leather tissue and "stretch" to read by a ballpoint pen.

Sewing fur hat

Gently cut through the planned line with a razor or a building knife without pressing the skin to the table, moving on the weight.

Sewing fur hat

From the bottom of the groin, it is easy to lay more superfluous in a fold and cut the handle, to cut up too much.

Sewing fur hat

Sew made slots using silk or piping threads. Fold the edges together, fur with a needle to fill in and sew two rolling stitch forward one back.

Sewing fur hat

Mix the skirt from the pulverizer in conventional water and pull on the smooth surface as possible to press the folds. I just nailed with small nails to a long-suffering ironing board. Leave to completely dry.

Sewing fur hat

Without removing the skin with a smooth surface, the range of the ridge is a dark strip on the fur. On the pattern previously made, also outline the desired line of the ridge. Next, decompose the pattern on the skin alignmenting these lines and circle the pattern with a ballpoint handle, not pressed, do not forget from the left and right edge to leave the stack on the seam of 4 mm.

Sewing fur hat

Mark the line of inflection of Niza and labels on the wedges.

Sewing fur hat

Build knife on the contour cut the pattern.

It is better to start a split from the place where there is no cut and move to the cutting part. Do not forget that you need to move on the weight, so that it would not cut the fur, otherwise the fur will have cropped propellas.

Sewing fur hat

Cutted pattern.

Sewing fur hat

Then folded the details of the two wedges on the left and to the right of the central seam of the connection and sew the way the part described above, for convenience you can make the part of the pin, but do not fond of it, the ebony of extra punctors does not like.

Sewing fur hat

Then sew a wedge opposite the seam and connect itself the seam itself, use the labels so that there are no shifts, otherwise the coat of the curve will work. The cap is ready.

Sewing fur hat

Now to the bottom of the cap in a circle you need to sew a woven tape or oblique beyk, again two stitches forward, one back.

Sewing fur hat

Then beate on the intended line of nose and for the woven tape with oblique stitches to sew the allowance.

Sewing fur hat

The upper part of the header is ready, proceed to the lining.

Sewing fur hat

For lining from Kliniev, use the original pattern, simply to the seam, add 1 cm for fuel freedom and 1 cm to allow the seams. My hat on Vatin and Pattern is a rectangle of wattin equal to the height of the cap 15-1.5 cm cm and scalp 54 cm +2 cm and the lining larger 2 cm below, on top and on the average seam of step 1 cm. Whatever batting on The lining was not saved to put the machine or sew manually in several places. Sew medium seam. I must say that I decided to take advantage of this type of lining, to have filling at the top of the header, since the hat above the head is somewhat cm. If I used the pattern with wedges or sewed without batting, then I needed to do in the pattern Heap cap less. Also, such a type of lining is suitable for any cap without a Vatine Top.

Sewing fur hat

In the upper border of the Wattin, to make the beaten and through the edge of strong threads to flash in a circle.

Sewing fur hat

To pull out that this is such a bag. Seam medium seam.

Sewing fur hat

Attach the lining inside, combine the average seams on the cap and lining. Sewing the lining is secret stitches to the tissue tape, combining lining bending with the border of fur and ribbon.

Sewing fur hat

Tighten the "bottom" lining, make fitting, maybe you need to tighten or weaken the screed. The lining should not be more fur cap. Remove the cap to fix the thread, distribute the assembly.

Sewing fur hat

On the diameter of the bottom to make this "tablet".

Sewing fur hat

Pinch to the bottom.

Sewing fur hat

Send secret stitches.

Sewing fur hat

Did you like the article? Subscribe to the channel to keep abreast of the most interesting materials

Subscribe

Today I want to tell how to sew a hat with the shape of the fur stripes.

We will need:

1) mink fur;

2) fox fur;

3) knitted fabric;

4) Ski knife;

5) needle on fur;

6) DOOL.

So, break.

We need a tricky canvas associated with a 2x2 elastic machine. 40 cm high and 40 facial path widths.

How to sew a hat from the fur: master class

We divide our canvas in the field, you can sell a contrasting thread. From this place we will sew fur strips.

Step the long side.

How to sew a fur hat with a stripe stripes method, photo number 1

Now we take a mink, it is necessary to stretch it before it (that is, to wet and in the stretched form, fasten on the board with nails. Give driving.)

Measure from the bottom two segments of 12 cm.

How to sew a fur hat with a fur strip stripes method, photo № 2

Cut the segments of the speed knife, while the left hand hold the edge of the fur and lifting it with his right hand, cut off. So that the knife does not touch the surface of the table and did not cut the ends of the fur.

How to sew a fur hat with a fur strip stripes method, photo number 3

We put the label by charting the middle. From the middle to the sides of the strip of a width of 0.8 cm.

How to sew a fur hat with a fur strip stripes method, photo № 4

We dwell on the strips as a speed knife. Total strips we need 40 pcs.

How to sew a fur hat for stripes of fur stripes, photo № 5

We also do the same with fox fur, only strip needed 6 cm long.

How to sew a fur hat with a fur stripe stripe method, photo № 6

How to sew a fur hat with a fur strip stripe method, photo № 7

How to sew a fur hat with a fur strip stripes method, photo number 8

Cutting it at 0.5 cm. Cut on strips.

We dress the knitted blank on the pour and begin to sew from the middle planted.

How to sew a fur hat with a fur strip stripe method, photo № 9

How to sew a fur hat with stripes of fur stripes, photo № 10

How to sew a fur hat with the stripes of fur stripes, photo № 11

Stitches make 0.5-0.7 cm, not forgetting at the beginning to make a "leaf". Doodle when working should lie on the knees. So more convenient, and the edge of the freeze rests on the table.

How to sew a fur hat with a fur stripes stripes method, photo № 12

How to sew a fur hat with a fur strip stripe method, photo № 13

So sew in a circle all 40 stripes.

That's what we should get.

How to sew a fur hat with a fur stripes stripes method, photo № 14

Now we take felt the most dense or in several layers of the fog.

A piece of genuine leather or suede with sides of 13 cm. Maja felt glue "moment" and stick to it. We put a circle blank, a diameter of 12 cm and a gloomy helium handle or any other to be seen.

Cut.

How to sew a fur hat with a fur strip stripes method, photo № 15

How to sew a fur hat with stripes with fur stripes, photo № 16

We take our knitted blank, turn over the fur inside.

How to sew a fur hat using a fur stripes stripes, photo № 17

I straighter the fur, we apply our "donyshko" and begin to sew.

How to sew a fur hat for stripes of fur stripes, photo № 18

Each stitch we sew a strip of fur. Stitch "Through the Edge". That is, they pierce the knitwear, the strip of fur and the bottom.

We bring the second side and also sew to the bottom.

How to sew a fur hat for stripes with fur stripes, photo № 19

How to sew a fur hat with a fur strip stripe method, photo № 20

We pave a line by car, 1 cm from the edge.

How to sew a fur hat with a fur strip stripes method, photo № 21

We take a piece of fleece, put the cap on the fleece, wrap the fleece on the cap and lay the line as 1 cm from the edge. Excess fleece cut.

How to sew a fur hat with a fur strip stripe method, photo № 22

How to sew a fur hat using a fur stripes by stripes, photo № 23

How to sew a fur hat for stripes of fur stripes, photo № 24

We take a bunch of gum and insert into the edge of the caps.

How to sew a fur hat with a fur strip stripes method, photo № 25

It remains to turn the header and combing the comb for fur with sharp teeth.

How to sew a fur hat with a fur strip stripes method, photo № 26

Thanks to everyone who read to the end. This is my first master class, do not judge strictly :)

Pattern of female hats from fur

Pattern of female hats from furWinter outside the window, and with it and frosts with snowdrifts.

It is necessary to somehow bask and warm.

So everyone runs to the store behind the warm hat, and who is online by the pattern, so that you can make themselves.

I looked at the prices of hats in stores, and abuned - how much they all stand!

I remember everything, how to keep a needle in your hand, and sew the caps themselves

Pattern caps are very simple (Although, I did not even imagine how simple it is!).

We move it on paper, and here the pattern of the caps are already ready.

Pattern date on size 54:

Pattern of female hats from fur

Now you need to sew it.

And if you need a pattern to adjacent size, then add around the missing size, and recalculate the corners of the wedges.

Tips for processing caps of artificial fur:

1. All seams on an artificial fur must necessarily need to descend or peel into pins, folded across the seam, due to this prevents the displacement of the layers of layers.

2. Binds of seams do not delete, but only to paint them to the sides with the help of a rings of scissors.

3. From the front side, carefully pull out the pushing pin from the seams.

The following describes the process of sewing caps:

1. First, you need to sew the cuttings on both sides of the header, ranging from the base of the wedges. From the wrong side, "splash" of the seams, swallowing them with rings of scissors.

 How to sew a fur hat for stripes of fur stripes, photo № 27

2. Details of the caps Sewing together, at the same time, attention to the fact that the skin does not stretch and not asleep. All seams must come together in the center of the dad.

How to sew a fur hat for stripes of fur stripes, photo № 27

3. Remove the dad on the wrong one and put the head on it with the head so that all the seams coincided. Head Side to the papata seam "Kozlik".

Attention: Fliselin is not glued to the cap, it is sewn from it the head necessary to give a dad shaped. On the pattern of the caps, clean the fliesline without an allowance for the bending along the bottom cut (the middle of the transition coincides with the folding tissue).

 How to sew a fur hat for stripes of fur stripes, photo № 27

So that it is rigid enough to pre-glue with iron two layers of fliseline by the adhesive side inside.

 How to sew a fur hat for stripes of fur stripes, photo № 27

4. Package at the bottom of the papahs. Unscrew to the wrong side.

Successful tailoring and success in creativity!

http://katushenka.ru/2010/10/31/sshit-shapku-iz-mexa-krolika-legko/

It is necessary to pay tribute to products from fur, because they do not lose their relevance from year to year. It is not surprising, because the fur not only can look stylish, but also keeps warm. And the preservation of heat in our latitudes is especially important.

Fur products will be found in the wardrobe of almost every woman. Perhaps love for products from fur occurs since the most ancient times.

The hunters have long been hunted to hunt and brought their own animal skins. Now the mink hat and other animal products are luxury, due to its high price.

But you should not despair, because it is possible to sew a fur hat with your own hands. It takes only your desire.

If you learn how to sew fur products, you not only be able to save your savings, but also replenish them by selling your products to girlfriends.

In the article below we will tell you in detail how to work with fur.

What fur is better to sew a hat

Summary:

When choosing fur to first place your financial capabilities and, of course, taste. When choosing a fur for a cap, it is worth noting that the hat is worn with a coat or a fur coat, respectively, they must be combined.

Below you can see the photo of the fur hat made by their own hands by our subscribers.

Fur hat with their own hands

A common capped model in women serves cap-tablet. She will suit absolutely any woman and perfectly combined with a coat or fur coat.

The most important thing is to choose its height. This hat visually increases the size of your head.

In order to sew such a cap, you need a fur, thread, lining, threads and needles, and, by itself, a sewing machine.

Pattern of the fur hat with their own hands consists of two elements. Circle and rectangle. In order to unmistakably draw the patterns, you need to measure the sizes of the head, we advise you to use the meter.

Choose height by personal sensations and addictions. As you could guess, you must have a rectangle, whose parties should be equal to the height of the cap.

In order to make a circle, use the resulting rectangle. Patterns are made on paper.

  • Step-by-step instruction
  • Secure the pins with the hook of the skin. Circle chalk and leave a place for seams about 2 cm.
  • Then cut the details of the razor.
  • We do all the same for lining material.
  • Sew the fur and lining with the involves to each other.
  • Connect the circle and rectangle by involve.
  • Machine to the typewriter with each other 1 cm from the edge.
  • To leather fur and lining pins.

Fur blank and lining are stitching and turned out

Cap of mink

The hat made of fur strips with their own hands is sewn along ordinary knitting technique with the only difference that thin strips of mink are imposed on the main yarn.

To begin with, bring the fur to a good condition. The skin must be cleared and remove the remnants of the glue, as well as combing. Next should be cut to the skin on the part, initially draw on it places of cuts.

When choosing the size of the strips, pay attention to only that they are one size. Fur should be cut in a well-fulnent item on weight.

The next step is a wool lining. Needlewomen, knit the founding of wool yarn. In order to associate, find out all the circuits of gum and holes.

Crochet knit columns with nakid and air loops between them. Holes make fat so that the fur can pass through them.

Next you need to make a lining. We make the pattern to suit your head. We grasp the lining. Slash holes at the same distance in width of fur strips. Wake up fur stripes in holes and fasteners inside with a thread and needle.

Conclusion

So, in this article, you studied ways to sew the fur hats with your own hands.

Making caps is very interesting and at the same time time-consuming occupation for beginners. But all the efforts spent are not in vain. After all, you not only saved a bunch of money, but also mastered the new skill.

And the things created with their own hands wearing doubly pleasant. You can also use and make a new hand from the old fur hat.

Stock Foto Fur hats do it yourself

To winter cold, such an important headdress should be prepared in advance. You can, of course, purchase a sample in the store, but also in advance to sew yourself to each woman for each woman.

Most of the ladies own the secrets of the cut of any soft material, they can sew on the sewing machine and manually, especially products from thick skin. Therefore, today we sew a fur hat with your own hands.

Your manual product, and in other words, Hand-Made, will serve you in all its functionality, and will also become the only one in your way: there will be no such thing.

Whether you will save the hat- "Beach" or a dad to wear in the central regions or a hat-to-guns for Siberia.

The main thing is that the patterns of female fur hats will be made with their own hands, and then turn into ready-made ruins or dads.

Stylish dad do it yourself

  • What will you need?
  • Fur artificial or leather lining. Warm head will, naturally, in the leather cap;
  • Textiles on the inner decoration;
  • Cat paper or tank;
  • soft meter;

Sewing machine, own or relatives, there are, as well as fixtures for marking, patterns, cutting and pre-manual flashing.

What should be performed before:

Fabric meter, set the scope. The pattern of the fur hat is prepared with her own hands with a real height in the form of a circle, draw it on paper, such a height of the future dad. You can apply a rectangular blank length.

Draw the pattern, copy it onto the trash or ordinary paper. Get a circle and a rectangular figure.

Transfer them to the back of the fur. A sharp knife or scalpel separated all parts. To the fur or skin remained intact after this operation, only the textile lining or leather base is necessary to cut through.

Cut the same twins on the fabric.

Separate the fabric and fur with extensions. Make the sides of the sides of the pins or go a wide light step manually so that the future hat does not crumble. Further, push the line, retreating for a centimeter from the edge.

Carefully determine the direction of the Village. They should rush to face. On this basis, and find the place of stitching with the circle of pattern.

Remove the two parts of the hood cap and secure the pins. As above, push for rapprochement of parts.

Next will go easier. Open the facial part by turning out of the inside, and where the pile is tightened under the threads of the lines, light it gently.

Like a hinting lining, but not completely. After inserting it into the dad, hurt the machine. The hat is ready, for a while try to put it on, but not on the head, but for something round it is for its size. It is desirable that it is based on a tight. Hold a couple of days, remove and wear on health.

Two-color fur hat

It should be not close, but contrasting: the best antagonists, the more beautiful there will be a ruin. His special density is not needed. It will also be a story about how to make a new hand from the old fur hat. After all, the overflow of used clothing is not a novelty in Russian families.

In addition to those specified in the section above the things needed to work, select a used knitting cap. We will need a sintepon and felt.

Cap from fur strips with your own hands - step-by-step instruction such:

- divide the fur piece to semisantimeter stripes, cut them out;

For the basis of the future cap (knitted used), sew the frame strips alternately contrasting coloring. Better will look like a hat, if the dark strips are somewhat shorten against the light gamma of fur. Crochet or ordinary needle with a thread, please contact the old knitting with fur.

Cut a piece of fleece or felt around the hole at the top (about twelve centimeters in diameter).

Think out which seam to you will seem best - just on top or somewhat recessed. To mitigate and better heat caps under the circle, put a sintepon.

Cap-Ushanka, Heated for Morozov

As materials to those listed above, add hammer and mini-nails, as well as a piece of plywood not thinner than five millimeters.

To begin with, as always, make the pattern of the cap, which can be made only from the pair of equilateral parts, ears and a visor. He is like on the header of Russian officers.

Next, you need to follow operations that are available on video, since the description cannot be immediately understood. It will be necessary to correctly cut and cut the eight different details of the future cap and sew them.

Explain only why the plywood is needed for the manufacture of the Winter Women's Hat. On this site, all the details are stacked in turns, moisten their fur, stretch how much you can, bring small hardware to the plywood. Wait for fur drying, remove the details from the board.

The last seas of the ears and the visor. Expand the product to the fur outside, strengthen the rigors for the risks of the ears when they are located at the top, or below with a strong frost.

And the things created with their own hands wearing doubly pleasant. You can also use and make a new hand from the old fur hat.

In each section of the article at the end of the work, make a photo of a fur hat made by your own hands.

Добавить комментарий